====== MBa8x DIP switch settings ====== 
=====Boot Modes=====

The following boot modes of the i.MX8 can be selected by the DIP switches S1 MBa8x. 

==== SD Card ====
<panel type="default" title="SD Card">
^ |:::  ^  SW1  ||||||
^ |:::  ^ ||||||  
^  DIP  |::: ^  1  ^  2  ^  3  ^  4  ^  5  ^  6  | 
^  ON  |:::  |     |     |  •  |  •  |     |     |
^  OFF  |::: |  •  |  •  |     |     |  •  |  •  |
</panel>
<panel type="default" title="eMMC">
^ |:::  ^  SW1  ||||||
^ |:::  ^ ||||||  
^  DIP  |::: ^  1  ^  2  ^  3  ^  4  ^  5  ^  6  | 
^  ON  |:::  |     |     |     |  •  |     |     |
^  OFF  |::: |  •  |  •  |  •  |     |  •  |  •  |
</panel>

<panel type="default" title="SPI NOR 3Byte Read">
^ |:::  ^  SW1  ||||||
^ |:::  ^ ||||||  
^  DIP  |::: ^  1  ^  2  ^  3  ^  4  ^  5  ^  6  |   
^  ON  |:::  |     |     |     |  •  |  •  |     |
^  OFF  |::: |  •  |  •  |  •  |     |     |  •  |
</panel>
<panel type="default" title="SPI NOR 4Byte Read">
^ |:::  ^  SW1  ||||||
^ |:::  ^ ||||||  
^  DIP  |::: ^  1  ^  2  ^  3  ^  4  ^  5  ^  6  |   
^  ON  |:::  |     |  •  |  •  |  •  |  •  |     |
^  OFF  |::: |  •  |     |     |     |     |  •  |
</panel>

<panel type="default" title="Hyperflash 1,8V">
^ |:::  ^  SW1  ||||||
^ |:::  ^ ||||||  
^  DIP  |::: ^  1  ^  2  ^  3  ^  4  ^  5  ^  6  |   
^  ON  |:::  |     |  •  |     |  •  |  •  |     |
^  OFF  |::: |  •  |     |  •  |     |     |  •  |
</panel>

<panel type="default" title="Serial Downloader">
^ |:::  ^  SW1  ||||||
^ |:::  ^ ||||||  
^  DIP  |::: ^  1  ^  2  ^  3  ^  4  ^  5  ^  6  |  
^  ON  |:::  |     |     |  •  |     |     |     |
^  OFF  |::: |  •  |  •  |     |  •  |  •  |  •  |
</panel>

<panel type="default" title="Boot from Fuses">
^ |:::  ^  SW1  ||||||
^ |:::  ^ ||||||  
^  DIP  |::: ^  1  ^  2  ^  3  ^  4  ^  5  ^  6  |  
^  ON  |:::  |     |     |     |     |     |     |
^  OFF  |::: |  •  |  •  |  •  |  •  |  •  |  •  |
</panel>


===== CAN configuration (S4) =====
DIP switch S4 is used to configure the CAN interfaces CAN1 and CAN2.

<WRAP half column>
==== Termination ====
^ DIP  ^ OFF (default)  ^  ON  ^
| S4-1 |  CAN0 not terminated  | CAN0 interface terminated (120Ω)  |
| S4-2 |  CAN1 not terminated  | CAN1 interface terminated (120Ω)  |
</WRAP>