===== STKa64xxL Boot Device Selection (S4, S5, S6, S7) =====

The following boot modes can be configured by setting the DIP switches S4, S5, S6, S7 on the MBa65xx.

<panel type="info" no-body="true" title="Boot Configuration">
<accordion collapsed="true">


<panel type="primary" title="SD-Card">

<grid>
<col sm="3">
<WRAP centeralign>
[size=150%]**S4**[/size]
{{ :en:dip_4_1100.png?nolink&150 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S5**[/size]
{{ :en:dip_4_001x.png?nolink&150 |}}
</WRAP>
</col>


<col sm="3">
<WRAP centeralign>
[size=150%]**S6**[/size]
{{ :en:dip_4_0100.png?nolink&150 |}}
</WRAP>
</col>


<col sm="3">
<WRAP centeralign>
[size=150%]**S7**[/size]
{{ :en:dip_4_xx00.png?nolink&150 |}}
</WRAP>
</col>
</grid>
</panel>


<panel type="primary" title="eMMC">

<grid>
<col sm="3">
<WRAP centeralign>
[size=150%]**S4**[/size]
{{ :en:dip_4_1100.png?nolink&150 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S5**[/size]
{{ :en:dip_4_001x.png?nolink&150 |}}
</WRAP>
</col>


<col sm="3">
<WRAP centeralign>
[size=150%]**S6**[/size]
{{ :en:dip_4_0000.png?nolink&150 |}}
</WRAP>
</col>


<col sm="3">
<WRAP centeralign>
[size=150%]**S7**[/size]
{{ :en:dip_4_xx00.png?nolink&150 |}}
</WRAP>
</col>
</grid>
</panel>

<panel type="primary" title="QSPI-NOR">

<grid>
<col sm="3">
<WRAP centeralign>
[size=150%]**S4**[/size]
{{ :en:dip_4_1100.png?nolink&150 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S5**[/size]
{{ :en:dip_4_1000.png?nolink&150 |}}
</WRAP>
</col>


<col sm="3">
<WRAP centeralign>
[size=150%]**S6**[/size]
{{ :en:dip_4_1xxx.png?nolink&150 |}}
</WRAP>
</col>


<col sm="3">
<WRAP centeralign>
[size=150%]**S7**[/size]
{{ :en:dip_4_xx00.png?nolink&150 |}}
</WRAP>
</col>
</grid>
</panel>


<panel type="primary" title="USB host (mass storage)">

<grid>
<col sm="3">
<WRAP centeralign>
[size=150%]**S4**[/size]
{{ :en:dip_4_1100.png?nolink&150 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S5**[/size]
{{ :en:dip_4_1010.png?nolink&150 |}}
</WRAP>
</col>


<col sm="3">
<WRAP centeralign>
[size=150%]**S6**[/size]
{{ :en:dip_4_1000.png?nolink&150 |}}
</WRAP>
</col>


<col sm="3">
<WRAP centeralign>
[size=150%]**S7**[/size]
{{ :en:dip_4_0000.png?nolink&150 |}}
</WRAP>
</col>
</grid>
</panel>


<panel type="primary" title="USB device (dfu-util)">

<grid>
<col sm="3">
<WRAP centeralign>
[size=150%]**S4**[/size]
{{ :en:dip_4_1100.png?nolink&150 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S5**[/size]
{{ :en:dip_4_1010.png?nolink&150 |}}
</WRAP>
</col>


<col sm="3">
<WRAP centeralign>
[size=150%]**S6**[/size]
{{ :en:dip_4_0000.png?nolink&150 |}}
</WRAP>
</col>


<col sm="3">
<WRAP centeralign>
[size=150%]**S7**[/size]
{{ :en:dip_4_0000.png?nolink&150 |}}
</WRAP>
</col>
</grid>
</panel>
</accordion>
</panel>

===== STKa64xxL Functional DIP Switches =====

<panel type="primary" title="CAN0 configuration (S1)">
DIP switch S1 is used to configure the CAN interfaces CAN0.
^  Funktion  ^  S11-1  ^  S11-2  ^
|  CAN-Bus not terminated  |  OFF  |  OFF  |
|  not defined (illegal state)  |  OFF  |  ON  |
|  not defined (illegal state)  |  ON  |  OFF  |
|  CAN-Bus terminated with 120 Ohm  |  ON  |  ON  |
</panel>



<panel type="primary" title="RS485 Termination (S3)">
DIP switch S4 is used to configure the RS485 interface.
^  DIP  ^  OFF (default)  ^  ON  ^
|  S4-1  |  RS485 RxD not terminated  |  RS485 RxD terminated (120Ω)  |
|  S4-2  |  RS485 TxD not terminated  |  RS485 TxD terminated (120Ω)  |
</panel>