====== MBa7x DIP switch settings ======
===== Boot Device Selection (S1, S2, S3 & S4) =====
To select the desired boot medium set the DIP switches S2, S3, S4 and S1 accordingly.



<panel type="primary" title="Boot Mode">

<grid>

<col sm="6">
To enable boot device selection BOOT_MODE has to be set to "Internal Boot".\\ This can be done using DIP switch 
S1 on MBa7x. \\

<callout type="warning" icon="true">
Switching boot sources is only possible if the BOOT_MODE fuses are not programmed. If configured for "Boot from eFuses" but fuses are not programmed, the boot loader will not be able to determine the boot source. 
</callout>
</col>
<col sm="6">

^ BOOT_MODE         ^  S1-1  ^  S1-2  ^
| Boot from eFuses  |  0   |  0   |
| Serial Downloader |  0   |  1   |
| Internal Boot     |  1   |  0   |

</col>
</grid>
</panel>
\\
The following boot modes of the i.MX7 can be selected by the DIP switches S1, S2, S3 and S4 on the MBa7x:


<panel type="primary" title="SD-Card">

<grid>
<col sm="3">
<WRAP centeralign>
[size=150%]**S1**[/size]
{{ :en:dip_2_10.png?nolink&85 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S2**[/size]
{{ :en:dip_8_01001000.png?nolink&270 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S3**[/size]
{{ :en:dip_8_00001000.png?nolink&270 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S4**[/size]
{{ :en:dip_4_0000.png?nolink&140 |}}
</WRAP>
</col>
</grid>
</panel>


<panel type="primary" title="eMMC">

<grid>
<col sm="3">
<WRAP centeralign>
[size=150%]**S1**[/size]
{{ :en:dip_2_10.png?nolink&85 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S2**[/size]
{{ :en:dip_8_00000100.png?nolink&270 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S3**[/size]
{{ :en:dip_8_00010100.png?nolink&270 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S4**[/size]
{{ :en:dip_4_0000.png?nolink&140 |}}
</WRAP>
</col>
</grid>
</panel>


<panel type="primary" title="SPI NOR">

<grid>
<col sm="3">
<WRAP centeralign>
[size=150%]**S1**[/size]
{{ :en:dip_2_10.png?nolink&85 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S2**[/size]
{{ :en:dip_8_00000000.png?nolink&270 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S3**[/size]
{{ :en:dip_8_00000010.png?nolink&270 |}}
</WRAP>
</col>

<col sm="3">
<WRAP centeralign>
[size=150%]**S4**[/size]
{{ :en:dip_4_0000.png?nolink&140 |}}
</WRAP>
</col>
</grid>
</panel>


----

===== Functional DIP Switches =====
DIP-Switch settings for CAN and RS485.

<grid>
<col sm="6">
<panel type="primary" title="CAN configuration (S5)">
DIP switch S5 is used to configure the CAN interfaces CAN1 and CAN2.
^  DIP  ^  OFF (default)  ^  ON  ^
|  S5-1  |  CAN0 not terminated  |  CAN0 interface terminated (120Ω)  |
|  S5-2  |  CAN1 not terminated  |  CAN1 interface terminated (120Ω)  |
</panel>
</col>

<col sm="6">
<panel type="primary" title="RS485 configuration (S6)">
DIP switch S6 is used to configure the RS485 interface.
^  DIP  ^  OFF (default)  ^  ON  ^
|  S6-1  |  RS485 RxD not terminated  |  RS485 RxD terminated (120Ω)  |
|  S6-2  |  RS485 TxD not terminated  |  RS485 TxD terminated (120Ω)  |
</panel>
</col>

</grid>



----