===== Starterkit Default DIP Switch Settings =====
By default the latest TQMLX2160A BSP has the following SerDes configuration:
^ SerDes module ^ SerDes protocol ^
| 1 | 14 |
| 2 | 11 |
| 3 | 2 |
Depending on the standard BSP SerDes configuration and boot source, the DIP switches must be configured as shown below:
==== SD Card ====
{{ :en:dip_4_1000.png?nolink&150 |}}
{{ :en:dip_4_1100.png?nolink&150 |}}
{{ :en:dip_4_1111.png?nolink&150 |}}
{{ :en:dip_4_0010.png?nolink&150 |}}
{{ :en:dip_2_10.png?nolink&85 |}}
==== QSPI NOR ====
{{ :en:dip_4_0000.png?nolink&150 |}}
{{ :en:dip_4_1100.png?nolink&150 |}}
{{ :en:dip_4_1111.png?nolink&150 |}}
{{ :en:dip_4_0010.png?nolink&150 |}}
{{ :en:dip_2_10.png?nolink&85 |}}
===== Starterkit Boot Source DIP Switch Settings =====
[size=150%]**S1**[/size]
{{ :en:dip_4_100x.png?nolink&150 |}}
[size=150%]**S1**[/size]
{{ :en:dip_4_010x.png?nolink&150 |}}
[size=150%]**S1**[/size]
{{ :en:dip_4_000x.png?nolink&150 |}}
==== MBLx2160A Configuration DIP (S1,S2,S3,S4, S5) ====
^ DIP ^ Function ^
^ 1 | BOOT_SRC0 |
^ 2 | BOOT_SRC1 |
^ 3 | BOOT_SRC2 |
^ 4 | NOR_SWAP# |
^ DIP ^ Function ^
^ 1 | EMMC_SEL0 |
^ 2 | EMMC_SEL1 |
^ 3 | EVDD_SEL |
^ 4 | LX_CONIG_RFU1 |
^ Function ^ EMMC_SEL0 ^ EMMC_SEL1 ^
| 8Bit eMMC | OFF | OFF |
| 4Bit eMMC + 2x I²C | OFF | ON |
| undefined | ON | OFF |
| SDHC2 on Module Connector | ON | ON |
^ DIP ^ Function ^ ON ^ OFF ^
^ 1 | SD1_MUX_SEL | SGMII | PCIe |
^ 2 | SD2_2_MUX_SE | SGMII | SATA |
^ 3 | SD2_3_MUX_SEL | SGMII | SATA |
^ 4 | SD2_4_MUX_SEL | mPCIe | SATA |
^ DIP ^ Function ^ ON ^ OFF ^
^ 1 | SD2_6_MUX_SEL | XFI | SGMII |
^ 2 | SD2_7_MUX_SEL | XFI | SGMII |
^ 3 | SD3_MUX_SEL | PCIe x8 (X37) | 2x PCIe x4 (X35, X36) |
^ 4 | ENABLE_FAN | Fan disabled | Fan enabled |
^ DIP ^ ON ^ OFF ^
^ 1 | EC2 Muxing | EC2 1588 Muxing |
^ 2 | --- | --- |