===== Prepare USB Stick for BIOS Update =====
<panel type="primary" title="BIOS Update USB Stick">


=== Prerequisites ===
   * FAT formated USB-Stick with at least > 32 MiB storage
   * Latest H2OFFT™ (Firmware Flash Tool)
<callout type="primary">
Due to licensing restrictions the H2OFFT is only available on request.\\
Please contact [[Support@tq-group.com|TQ Support]] for further information.
</callout>

=== USB Stick ===
Copy Insyde Firmware Flash Tool to USB-Stick\\ <code>
<USB key>
    ├───H2OFFT-Sx64.efi
</code>
The BIOS-Update-USB Stick is now ready for updating and flashing BIOS images.\\
For further Information please see the following section.
</panel>
===== @mod_name@  BIOS Update =====
<panel type="primary" title="Update BIOS">
=== Prerequisites ===
   *Prepared USB Stick with BIOS Update Tool
   *BIOS File @bios_image_name@_@bios_image_version@.bin
   *Copy BIOS File to USB Stick
<code>
<USB key>
    ├─── H2OFFT-Sx64.efi
    ├─── @bios_image_name@_@bios_image_version@.bin   
</code>

=== Perform BIOS Update ===
<callout type="info">
Attention: keyboard layout is US by default in the BIOS setup!
</callout>

  - Insert BIOS-Update-USB Stick stick to a Starterkit USB port\\
  - Power the starter kit and enter the BIOS by repeatedly pressing ESC\\
  - Navigate to the tab "Boot" and set the boot type to "Dual Boot Type"\\
  - Enable @bios_me_txe_enable@ option in the BIOS Menu @bios_me_enable_path@
  - <F10> to save the settings and reboot the system\\ <alert type="info">To check if the system is prepared for the Firmware Update you can check the //Intel ME-Version// Number on the MAIN page. It should be **0.0.0.0**</alert>
  - After reboot navigate into the EFI Shell (Boot Manager > Internal EFI Shell)\\
  - After starting the EFI Shell switch path to the USB stick by typing ''fs0:''. This depends on the amount of connected mass storage devices. With command ''ls'' you can check the content of the path.\\
  - Launch BIOS update\\

<code>
H2OFFT_Sx64.efi @bios_image_name@_@bios_image_version@.bin @bios_update_parameter@
</code>

 ⇒ BIOS will reboot into EFI shell after the update has finished succesfully
</panel>
===== Boot from the external BIOS  =====
<panel type="primary" title="Work with external BIOS"> 
The BIOS source can be selected on the (@mod_name@) SPI flash via connector @bios_jumper_mb@ on @mb_name@. 
^  @bios_jumper_mb@  ^^
^  Open  | BIOS will load from internal SPI Flash | 
^  Close  | BIOS will load from external SPI Flash |
</panel>
=== Supported external SPI flash devices ===
<panel type="primary" title="Supported Devices">
The following SPI flash devices are supported:
^ Platform/Module       ^ SPI flash device  ^ SPI flash vendor  ^
|@mod_name@  |@spi_flash_device@  |@spi_flash_vendor@  |

<accordion collapsed="true">
<panel type="primary" title="Flash BIOS to Carrier SPI Flash Chip">
===== @mod_name@ Flash BIOS to Carrier SPI Flash Chip =====
Flashing the Carrier SPI Chip is only possible with a working module.

**How to:**
  - Connect USB key with desired BIOS file and Insyde Update Tool „H2OFFT-Sx64“
  - **Open** the Boot Jumper @bios_jumper_mb@ (on Carrier)
  - Apply the supply voltage of 12 V; The sytem boot in the EFI Shell 
  - Enable "@bios_me_txe_enable@" in the BIOS and press F10 to save the configuration an reset the module
<alert type="info">This step is only nessesary for the TQMxE39x Modules</alert>
  - Navigate into the EFI-Shell
  - In the EFI Shell, switch path to the USB key
  - **Close** the Boot Jumper @bios_jumper_mb@ (on Carrier)
  - Execute BIOS Update with the following commands:
<code>
Shell> fs0: <Enter>
fs0:> H2OFFT_Sx64.efi @bios_image_name@_@bios_image_version@.bin @bios_update_parameter@ -N
</code>
  - **Open** the Boot Jumper @bios_jumper_mb@ (on Carrier) after a successful BIOS Update
  - Turn off the supply voltage
  - Finish. Now you can update modules with the Carrier SPI Flash Chip

</panel>
<panel type="primary" title="BIOS Recovery through the Carrier SPI Flash Chip">
===== @mod_name@ BIOS Recovery through the Carrier SPI Flash Chip =====

To recover the onboard BIOS with the Carrier SPI Flash Chip, a preflashed BIOS SPI Chip is required.\\
Please see //**Flash BIOS to Carrier SPI Flash Chip**// above.

**How To:**
  - Connect USB key with desired BIOS file and Insyde Update Tool „H2OFFT-Sx64“
  - **Close** the Boot Jumper @bios_jumper_mb@ (on Carrier)
  - Apply the supply voltage of 12 V; The sytem boot in the EFI Shell 
  - Enable "@bios_me_txe_enable@" in the BIOS and press F10 to save the configuration an reset the module
<alert type="info">This step is only nessesary for the TQMxE39x Modules</alert>
  - Navigate into the EFI-Shell
  - In the EFI Shell, switch path to the USB key
  - **Open** the Boot Jumper @bios_jumper_mb@ (on Carrier)
  - Execute BIOS Update with the following commands:
<code>
Shell> fs0: <Enter>
fs0:\> H2OFFT_Sx64.efi @bios_image_name@_@bios_image_version@ @bios_update_parameter@ -N
</code>
  - After successful BIOS Update reset the Module
  - Finished. You have successfully recovered the onboard BIOS
</panel>
</accordion>
</panel>