Prepare USB Stick for BIOS Update

Due to licensing restrictions the H2OFFT is only available on request.
Please contact TQ Support for further information.

Copy Insyde Firmware Flash Tool to USB-Stick

<USB key>
    ├───H2OFFT-Sx64.efi

The BIOS-Update-USB Stick is now ready for updating and flashing BIOS images.
For further Information please see the BIOS Update section.

@mod_name@ BIOS Update

<USB key>
    ├─── H2OFFT-Sx64.efi
    ├─── @bios_image_name@_@bios_image_version@.bin

Attention: keyboard layout is US by default in the BIOS setup!

Insert BIOS-Update-USB Stick stick to a Starterkit USB port
First enable @bios_me_txe_enable@ option in the BIOS Menu @bios_me_enable_path@
<F10> to save the settings and reboot the system
After reboot navigate into the EFI Shell (Boot Manager > Internal EFI Shell)
After starting the EFI Shell switch path to the USB stick by typing fs0:. This depends on the amount of connected mass storage devices. With command ls you can check the content of the path.
Launch BIOS update

H2OFFT_Sx64.efi @bios_image_name@_@bios_image_version@.bin @bios_update_parameter@

⇒ BIOS will reboot into EFI shell after the update has finished succesfully

Shell> exit

Select “Boot Manager”
Select desired boot device (e.g. Internal HD)
⇒ System will boot from selected boot device

The BIOS source can be selected on the (@mod_name@) SPI flash via connector @bios_jumper_mb@ on @mb_name@.

@bios_jumper_mb@
Open	BIOS will load from internal SPI Flash
Close	BIOS will load from external SPI Flash

The following SPI flash devices are supported:

Platform/Module	SPI flash device	SPI flash vendor
@mod_name@	@spi_flash_device@	@spi_flash_vendor@

Flashing the Carrier SPI Chip is only possible with a working module.

How to:

Connect USB key with desired BIOS file and Insyde Update Tool „H2OFFT-Sx64“
Open the Boot Jumper @bios_jumper_mb@ (on Carrier)
Apply the supply voltage of 12 V; The sytem boot in the EFI Shell
Enable “@bios_me_txe_enable@” in the BIOS and press F10 to save the configuration an reset the module
Navigate into the EFI-Shell
In the EFI Shell, switch path to the USB key
Close the Boot Jumper @bios_jumper_mb@ (on Carrier)
Execute BIOS Update with the following commands:

Shell> fs0: <Enter>
fs0:> H2OFFT_Sx64.efi @bios_image_name@_@bios_image_version@.bin @bios_update_parameter@ -N

Open the Boot Jumper @bios_jumper_mb@ (on Carrier) after a successful BIOS Update
Turn off the supply voltage
Finish. Now you can update modules with the Carrier SPI Flash Chip

To recover the onboard BIOS with the Carrier SPI Flash Chip, a preflashed BIOS SPI Chip is required.
Please see Flash BIOS to Carrier SPI Flash Chip

How To:

Connect USB key with desired BIOS file and Insyde Update Tool „H2OFFT-Sx64“
Close the Boot Jumper @bios_jumper_mb@ (on Carrier)
Apply the supply voltage of 12 V; The sytem boot in the EFI Shell
Enable “@bios_me_txe_enable@” in the BIOS and press F10 to save the configuration an reset the module
Navigate into the EFI-Shell
In the EFI Shell, switch path to the USB key
Open the Boot Jumper @bios_jumper_mb@ (on Carrier)
Execute BIOS Update with the following commands:

Shell> fs0: <Enter>
fs0:\> H2OFFT_Sx64.efi @bios_image_name@_@bios_image_version@ @bios_update_parameter@ -N