BIOS Revision | BIOS Version | CSE Firmware Version | BIOS Binary |
---|---|---|---|
Rev. 0106 | 05.45.47.23.11 | 15.40.30.2879 | TQMxE40S_05.45.47.23.11.bin |
Rev. 0105 ETH-PHY Quick-Fix-Release of Rev. 0104 | 05.43.49.16.09 | 15.40.16.2485 | TQMxE40S_05.43.49.16.09.bin |
Rev. 0104 Not for Windows older than 21H2! | 05.43.49.16.06 | 15.40.16.2485 | TQMxE40S_05.43.49.16.06.bin |
Rev. 0103 | 05.43.27.14.04 | 15.40.15.2416 | TQMxE40S_05.43.27.14.04.bin |
Rev. 0102 | 05.43.27.14.03 | 15.40.15.2416 | TQMxE40S_05.43.27.14.03.bin |
Rev. 0100 | 05.43.05.11.01 | 15.40.0.2204 | TQMxE40S_05.43.05.11.01.bin |
TQMxE40S 05.43.49.16.06
MD5SUM:79D3E41F15AD4B3FDA9F018E3F635427
TQMxE40S 05.43.27.14.04
MD5SUM:3E57C2A53EE4384AB5C2E2A514638CAC
TQMxE40S 05.43.27.14.03
MD5SUM:AE8964DC061AA6F74D30E55CCECFB8FC
TQMxE40S 05.43.05.11.01
MD5SUM:A9DEFF7102AED5B316F48C6F6436F096
TBD
Details | |
---|---|
Issue | The matching SPI chip for the socket on the MB-SMARC-3 is not yet available. |
Affected Revisions | |
BIOS | all revisions |
Module | TQMxE40S, all revisions |
Mainboard | MB-SMARC-3, all revisions |
Solution | |
Fix | Please contact TQ-Support if the module does not start due to a corrupted BIOS. |
Details | |
---|---|
Issue | Currently there is no software support for the used I2S codec chip (TLV320AIC3294) on the MB-SMARC-3 from the chip manufacturer. |
Affected Revisions | |
BIOS | all revisions |
Module | TQMxE40S, all revisions |
Mainboard | MB-SMARC-3, all revisions |
Solution | |
Fix | Please contact TQ-Support if you have questions about I2S. |
To activate or deactivate eMMC Support apply the following settings:
1. Boot the system into the BIOS menu
2. Set up 'SCS/SCC Configuration' option in the BIOS Menu accordingly:
BIOS Frontpage > Setup Utility > Advanced (Tab) > RC Advanced Menu > PCH-IO Configuration > SCS Configuration > eMMC 5.1 Controller = <Enabled>
3. Press <F10> to save the settings and reboot the system
To activate or deactivate SD Card Support apply the following settings:
1. Boot the system into the BIOS menu
2. Set up 'SCS/SCC Configuration' option in the BIOS Menu accordingly:
BIOS Frontpage > Setup Utility > Advanced (Tab) > RC Advanced Menu > PCH-IO Configuration > SCS Configuration > eMMC 5.1 Controller = <Enabled> BIOS Frontpage > Setup Utility > Advanced (Tab) > RC Advanced Menu > PCH-IO Configuration > SCS Configuration > SDCard 3.0 Controller = <Enabled>
3. Press <F10> to save the settings and reboot the system
To activate the NVMe (PCIe SSD) Support apply the following settings:
1. Boot the system into the BIOS menu
2. Set up 'PCI Express Root Port 2' option in the BIOS Menu accordingly:
BIOS Frontpage > Setup Utility > Advanced (Tab) > RC Advanced Menu > PCH-IO Configuration > PCI Express Root Port 2 = <disabled>
3. Press <F10> to save the settings and reboot the system
To activate or deactivate console redirection apply the following settings:
1. Boot the system into the BIOS menu
2. Set up 'Console Redirection' option in the BIOS Menu accordingly:
BIOS Frontpage > Setup Utility > Advanced (Tab) > Console Redirection > Console Serial Redirect = <Enabled>
3. Select and activate the desired UART port:
COMx > PortEnable = <Enabled>
Press <F10> to save the settings and reboot the system
Now the UEFI interface will be printed on the desired port with the Serial Port settings.
UEFI Firmware | MB-SMARC-3 |
---|---|
COM1 | SER0 (X43) |
COM2 | SER1 (X42) |
SerialIo-UART1 | SER3 (X35) |
SerialIo-UART2 | SER2 (X36) |
There are several ways to reset the UEFI firmware settings to the default values.
The UEFI settings can be reset by pressing F9 in the UEFI. You have to be in the Setup Utility Page to use this function.
To reset the settings without the display, proceed as follows:
When updating the UEFI firmware, the firmware defaults are loaded and all changes to the settings are lost.
Installing the same firmware resets these settings (e.g. UEFI update under Windows).
Our modules provide a function that allows to reset the UEFI to default values in case of emergency.
For this, the reset button must be pressed three times within one second.
If the module LED blinks red for a short time the reset to defaults was successful.