Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
en:arm:tqma8xx:mba8xx:dip_switches [2019/01/14 13:32] – created liedmannen:arm:tqma8xx:mba8xx:dip_switches [2022/08/04 15:02] (current) – external edit 127.0.0.1
Line 1: Line 1:
-<WRAP round important>**Work in Progress**</WRAP> +====== MBa8Xx DIP switch settings ======  
-==== SD card ==== +=====Boot Modes===== 
-^ |:::  ^  S1  |||+ 
-^ |:::  ^ {{ :en:arm:tqma8x:mba6x:mba6x_s1_sd.png?nolink&100 |}}|||| +The following boot modes of the i.MX8X can be selected by the DIP switch S1 on the MBa8Xx.  
-^  DIP  |::: ^   ^       | +<grid> 
-^  ON  |:::    |  •  |  •   +<col sm="2"> 
- OFF  |::: | • |  •   |  | +<panel type="primary" title="SD-Card"> 
 +<WRAP centeralign> 
 +[size=150%]**S1**[/size] 
 +{{ :en:dip_4_0011.png?nolink&150 |}} 
 +</WRAP> 
 +</panel> 
 +</col> 
 + 
 + 
 +<col sm="2"> 
 +<panel type="primary" title="eMMC"> 
 +<WRAP centeralign> 
 +[size=150%]**S1**[/size] 
 +{{ :en:dip_4_0010.png?nolink&150 |}} 
 +</WRAP> 
 +</panel> 
 +</col> 
 + 
 +<col sm="2"> 
 +<panel type="primary" title="QSPI NOR"> 
 +<WRAP centeralign> 
 +[size=150%]**S1**[/size] 
 +{{ :en:dip_4_0110.png?nolink&150 |}} 
 +</WRAP> 
 +</panel> 
 +</col> 
 + 
 + 
 +<col sm="3"> 
 +<panel type="primary" title="Serial Downloader"> 
 +<WRAP centeralign> 
 +[size=150%]**S1**[/size] 
 +{{ :en:dip_4_0001.png?nolink&140 |}} 
 +</WRAP> 
 +</panel> 
 +</col> 
 + 
 +<col sm="3"> 
 +<panel type="primary" title="Boot from Fuses"> 
 +<WRAP centeralign> 
 +[size=150%]**S1**[/size] 
 +{{ :en:dip_4_0000.png?nolink&140 |}} 
 +</WRAP> 
 +</panel> 
 + 
 +</col> 
 +</grid> 
 + 
 + 
 + 
 + 
 + 
 +===== Functional DIP Switches ===== 
 +DIP-Switch settings for DP-Bridge and CAN. 
 + 
 +<grid> 
 +<col sm="6"> 
 +<panel type="primary" title="DSI-to-DP-Bridge (S9)"> 
 +<alert type="warning"> Only available on MBa8Xx Rev.01xx</alert> 
 +^  DIP  ^  S9  ^ 
 + ON   enable DSI-to-DP-Bridge  
 + OFF  |  use LVDS interface  | 
 +</panel> 
 +</col> 
 + 
 +<col sm="6"> 
 +<panel type="primary" title="CAN configuration (S7)"> 
 +DIP switch S7 is used to configure the CAN interfaces CAN1 and CAN2. 
 +^  DIP   OFF (default)   ON  ^ 
 +|  S7-1  |  CAN0 not terminated  |  CAN0 interface terminated (120Ω)  | 
 +|  S7-2   CAN1 not terminated   CAN1 interface terminated (120Ω)  | 
 +</panel> 
 +</col> 
 + 
 +</grid> 
 + 
 + 
 + 
  • Last modified: 2022/08/04 15:04