User Tools

Site Tools


vmware.png nfs.png tftp.png subversion.png eclipse.png logo.png tutorial.png

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
en:arm:tqmls10xxa:mbls10xxa:dip_switches [2019/04/15 11:56]
liedmann created
en:arm:tqmls10xxa:mbls10xxa:dip_switches [2019/04/25 15:41] (current)
liedmann added pictures
Line 1: Line 1:
 <WRAP round important>​Work in Progress</​WRAP>​ <WRAP round important>​Work in Progress</​WRAP>​
 +
 +===== Boot Device Selection (S5) =====
 +To select the desired boot medium set the DIP switches accordingly
 +
 +==== SD card ====
 +
 +^ |:::  ^  S5  ||||
 +^ |:::  ^  {{ :​en:​arm:​tqmls10xxA:​mbls10xxa:​dip_4_001x.jpg?​nolink&​60 |}}  ||||   
 +^  DIP  |::: ^  1  ^  2  ^  3  ^  4  |
 +^  ON  |:::|  |  |  •  ^ ^              ​
 +^  OFF  |:::|  •  |  •  |  ^ ^       
 +
 +
 +==== eMMC ====
 +
 +^ |:::  ^  S5  ||||
 +^ |:::  ^  {{ :​en:​arm:​tqmls10xxa:​mbls10xxa:​dip_4_x11x.jpg?​nolink&​60 |}}  ||||   
 +^  DIP  |::: ^  1  ^  2  ^  3  ^  4  |
 +^  ON  |:::|  •  |   ​| ​ •  ^ ^              ​
 +^  OFF  |:::|  |  •  |  ^ ^     
 +
 +==== QSPI ====
 +
 +^ |:::  ^  S5  ||||
 +^ |:::  ^  {{:​en:​arm:​tqmls10xxa:​mbls10xxa:​dip_4_x11x.jpg?​nolink&​60|}} ​ ||||   
 +^  DIP  |::: ^  1  ^  2  ^  3  ^  4  |
 +^  ON  |:::^ |  •  |  •  ^ ^              ​
 +^  OFF  |:::^ |  |  ^ ^     
 +
 +
 +==== MBLS10xxA Configuration DIP (S6,S7,S8) ====
 +
 +<WRAP centeralign>​
 +^   ​S6 ​  ^^^
 +^ DIP ^  ON  ^  OFF  ^
 +^ 1 | SerDes1 Lane A - SGMII  | SerDes1 Lane A - QSGMII ​ | 
 +^ 2 | SerDes1 Lane B - SGMII  | SerDes1 Lane B - QSGMII ​ |
 +^ 3 | SerDes1 Lane D - SGMII  | SerDes1 Lane D - XFI2  |
 +^ 4 | SerDes2 Lane B - MPCIe  | SerDes2 Lane B - SGMII  |
 +\\
 +^   ​S7 ​  ^^^
 +^ DIP ^  ON  ^  OFF  ^
 +^ 1 | QSGMII1 CLK SEL - 156.25 MHz  | QSGMII1 CLK SEL - 125 MHz  | 
 +^ 2 | QSGMII PHY1 CONFIG - QSGMII to Copper ​ | QSGMII PHY1 CONFIG - SGMII to Copper ​ |
 +^ 3 | QSGMII2 CLK SEL - 156.25 MHz  | QSGMII2 CLK SEL - 125 MHz  |
 +^ 4 | QSGMII PHY2 CONFIG - QSGMII to Copper ​ | QSGMII PHY2 CONFIG - SGMII to Copper ​ |
 +\\    ​
 +^   ​S8 ​  ^^^
 +^ DIP ^  ON  ^  OFF  ^
 +^ 1 | SerDes2 Lane D - PCIe  | SerDes2 Lane D - Mux for MPCIE/​SATA ​ | 
 +^ 2 | SerDes2 Lane D - SATA  | SerDes2 Lane D - MPCIE  |
 +^ 3 | Demuxing turn off  | Demuxing turn on  |
 +^ 4 | SerDes1 REF CLK2 - 156.25 MHz  | SerDes1 REF CLK2 - 125 MHz  |
 +\\  ​
 +</​WRAP>​
 +
 +
 +
 +
 +
 +
 +

en/arm/tqmls10xxa/mbls10xxa/dip_switches.1555322187.txt.gz · Last modified: 2019/04/15 11:56 by liedmann


Disclaimer

TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.


Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
Recent changes RSS feed Valid XHTML 1.0 Valid CSS Driven by DokuWiki