User Tools

Site Tools


vmware.png nfs.png tftp.png subversion.png eclipse.png logo.png tutorial.png

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
en:x86:tqmxe39s:bios_overview [2018/09/12 14:11]
bujupib created
en:x86:tqmxe39s:bios_overview [2018/09/13 16:26] (current)
schmid updated TXE FW version + PCI configurations
Line 1: Line 1:
-gfrgfgfg+^  BIOS Revision ​ ^  TXE Firmware Version ​ ^  PCI Configurations ​ ^  BIOS Binary ​ ^ 
 +|  **5.12.09.16.03** ​ |  3.1.50.2222 ​ |  4x1 PCIe Lanes  | TQMxE39S_5.12.09.16.03.bin ​ | 
 +^  ^^^^ 
 +|  **5.12.09.16.02** ​ |  3.1.50.2222 ​ |  4x1 PCIe Lanes  | TQMxE39S_5.12.09.16.02.bin ​ | 
 +|  :::  |  :::  |  1x4 PCIe Lanes  | TQMxE39S_5.12.09.16.02_PCIe_1x4.bin ​ | 
 +|  :::  |  :::  |  1x2 + 2x1 PCIe Lanes  | TQMxE39S_5.12.09.16.02_PCIe_1x22x1.bin ​ | 
 + 
 + 
 +===== Changelog ===== 
 + 
 +++++ 5.12.09.16.03 | 
 +  *Integrate 8Gb memory chip configuration 
 +  *correct GPIO adress 
 +++++ 
 +++++ 5.12.09.16.02 | 
 +  *adapt setup menu (hide many entries) 
 +  *update setup defaults to the TQMxE39S 
 +  *correct LVDS resolutions in SioTqmx86 driver  
 +  *configure GPI interrupt as level-triggered 
 +  *add menu to enable GPI interrupt IRQ12 
 +  *add and adapt new TXE FW 3.1.50.2222 
 +  *fix wrong negative temperature  
 +  *adapt temperature string 
 +  *enable all PCIe roots 
 +  *enable RTS/CTS in SioTqmx86 driver 
 +  *identify two or four chip memory configuration 
 +  *fix missing memory channels in SCU 
 +  *CPU to DRAM mapping for LPDDR4 
 +  *Fix not working HSUARTS as COM Ports 
 +  *Fix not working Over Current on USB0 
 +  *Fix not working USB3 after integrate TXE  
 +  *Unhide "​HDMI/​DVI"​ to use 4K monitors 
 +  *Fix not working SPI Flash GD 25LQ128D 
 +  *Disable UART Postcode support 
 +++++ 
 + 

en/x86/tqmxe39s/bios_overview.1536754262.txt.gz · Last modified: 2018/09/12 14:11 by bujupib


Disclaimer

TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.


Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
Recent changes RSS feed Valid XHTML 1.0 Valid CSS Driven by DokuWiki