Differences

This shows you the differences between two versions of the page.

--- en:layerscape:tqmls10xxa:linux:yocto:deployment_yocto [2020/04/07 11:04] – created liedmann
+++ en:layerscape:tqmls10xxa:linux:yocto:deployment_yocto [2023/11/08 13:55] (current) – removed work in progress liedmann
@@ Line 1: / Line 1: @@
-<WRAP round important>WORK IN PROGRESS</WRAP>
+<embed en:templates:tabs_yocto_bootstrap>
-<embed en:templates:tabs_yocto>
   <label product_type>Embedded module</label>
   <label lang>en</label>
@@ Line 12: / Line 11: @@
 </embed>
 \\
+<embed en:templates:deployment_yocto_bootstrap>
+<label lang>en</label>
+<label mod_arch>layerscape</label>
+<label bsp_name>linux</label>
+<label build_system>yocto</label>
+<label mod_name_code>tqmls10xxa</label>
+<label bsp_image_name>tq-image-generic-tqmls10xxa-mbls10xxa</label>
+<label mb_name_code>mbls10xxa</label>
+<label mb_name>MBLS10xxA</label>
+<label mod_name>TQMLS10xxA</label>
+<label mod_name_partition>TQMLS10xxA</label>
+<label stk_name>STKLS10xxA</label>
+<label eth_prime></label>
+<label uboot_default>u-boot-esdhc-2018.07-r0.bin</label>
+<label fdt_default>fsl-tqmls1046a-mbls10xxa.dtb</label>
+<label kernel_default>Image</label>
+<label update_uboot_cmd>update_uboot_mmc</label>
+<label update_dtb_cmd>update_fdt_mmc</label>
+<label update_kernel_cmd>update_kernel_mmc</label>
+</embed>
+===== Updating existing firmw
+are over ethernet new =====
+\\
+A good approach to update the firmare components U-Boot,Linux kernel and devicetree in a running system is to load them from a TFTP server. Therefore a running TFTP server is required in your network environment, please see the[[en:general_information:tftp|how to setup TFTP Server]] page how to setup on your development host.
+After setting up the TFTP server, the binaries that should be updated must be copied into the TFTP directory of your TFTP Server.
+==== Update Process ====
+. Setup the Starterkit to boot from SD/eMMC or QSPI,  please see the [[ .:..:..:mbls10xxA:dip_switches|Starterkit dip switch page]] how to setup\\
+. Connect the kit to the network with TFTP server supplying the binaries via ethernet on connector<label eth_prime>ETH_PRIME</label> \\
+. Power up the system and interrupt the boot process in U-Boot\\
+<code>
+Hit any key to stop autoboot:  0
+=>
+</code>
+. Setup the ethernet interface:
+++++ Set network settings manually |
+Provide the correct network configuration in U-Boot:
+<code>
+=> setenv autoload no
+=> setenv serverip <serverip>  (IP address of your TFTP server e.g.: setenv serverip 192.168.100.110)
+=> setenv ipaddr <ipaddr>      (e.g.: setenv ipaddr 192.168.100.111)
+=> setenv netmask <netmask>    (e.g.: setenv netmask 255.255.255.0)
+</code>
+++++
+++++ Set network settings using DHCP |
+If a DHCP server is available in the network, the interface can be configured by the server:
+<code>
+=> setenv autoload no
+=> setenv serverip <serverip>   (IP address of your TFTP server e.g.: setenv serverip 192.168.100.110)
+=> dhcp (get IP from server)
+</code>
+++++
+\\
+**5. Set U-Boot environment variables according to the image file name stored on the tftp server:**\\
+\\
+__**eMMc/SD Card**__
+For U-Boot update on eMMC/SD Card :      <code>=> setenv uboot_mmc <filename> (e.g.: setenv uboot_mmc u-boot-with-spl-pbl.bin)</code>
+__**QSPI NOR**__
+For U-Boot update on QSPI NOR :      <code>=> setenv uboot_qspi <filename> (e.g.: setenv uboot_spi_file fip_uboot.bin)</code>
+__**Devicetree**__
+For Device Tree update on eMMC/SD Card and QSPI NOR : <code>=> setenv fdt_file <filename> (e.g.: setenv fdt_file fsl-tqmls1043a-mbls10xxa.dtb)</code>
+__**Kernel**__
+For Kernel update on eMMC/SD Card and QSPI NOR
+:
+<code>=> setenv kernel <filename> (e.g.: setenv kernel Image.gz)</code>
+__**Frame Manager**__
+For Frame Manager Microcode on eMMC/SD Card and QSPI NOR : <code>=> setenv fmucode <filename> (e.g.: setenv fmucode  fsl_fman_ucode_ls1043_r1.1_106_4_18.bin)</code>
+\\
+**6. Perform Update: **
+__**U-Boot**__
+<code>
+eMMC /SD Card :   => run update_uboot_mmc
+QSPI NOR :        => run update_uboot_qspi
+</code>
+__**Devicetree**__
+<code>
+eMMC /SD Card :   => run update_fdt_mmc
+QSPI NOR :        => run update_fdt_qspi
+</code>
+__**Kernel**__
+<code>
+eMMC /SD Card :   => run update_kernel_mmc
+QSPI NOR :        => run update_kernel_qspi
+</code>
+__**Frame Manager**__
+<code>
+eMMC /SD Card :   => run update_fmucode_mmc
+QSPI NOR :        => run update_fmucode_qspi
+</code>
 \\