Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
en:layerscape:tqmlx2160a:mblx2160a:dip_switches [2020/12/17 10:30] – created weinholdo | en:layerscape:tqmlx2160a:mblx2160a:dip_switches [2023/02/14 15:37] (current) – updated S4 for the serdes franzwesselmann | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== Starterkit default DIP switch settings | + | ===== Starterkit |
- | === MBLX2160A | + | |
+ | By default | ||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | ^ SerDes module | ||
+ | | 1 | 14 | | ||
+ | | 2 | 11 | | ||
+ | | 3 | 2 | | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | Depending on the standard BSP SerDes configuration and boot source, the DIP switches must be configured as shown below: | ||
+ | |||
+ | ==== SD Card ==== | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | |||
+ | ==== QSPI NOR ==== | ||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | |||
+ | ===== Starterkit Boot Source DIP Switch Settings | ||
< | < | ||
Line 31: | Line 135: | ||
</ | </ | ||
</ | </ | ||
+ | |||
+ | ==== MBLx2160A Configuration DIP (S1, | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | ^ DIP ^ Function | ||
+ | ^ 1 | BOOT_SRC0 | ||
+ | ^ 2 | BOOT_SRC1 | ||
+ | ^ 3 | BOOT_SRC2 | ||
+ | ^ 4 | NOR_SWAP# | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | |||
+ | ^ DIP ^ Function | ||
+ | ^ 1 | EMMC_SEL0 | ||
+ | ^ 2 | EMMC_SEL1 | ||
+ | ^ 3 | EVDD_SEL | ||
+ | ^ 4 | LX_CONIG_RFU1 | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | ^ | ||
+ | | 8Bit eMMC | OFF | OFF | | ||
+ | | 4Bit eMMC + 2x I²C | OFF | ON | | ||
+ | | undefined | ||
+ | | SDHC2 on Module Connector | ON | ON | | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | | ||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | |||
+ | ^ DIP ^ Function | ||
+ | ^ 1 | SD1_MUX_SEL | ||
+ | ^ 2 | SD2_2_MUX_SE | ||
+ | ^ 3 | SD2_3_MUX_SEL | ||
+ | ^ 4 | SD2_4_MUX_SEL | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | |||
+ | ^ DIP ^ Function | ||
+ | ^ 1 | SD2_6_MUX_SEL | ||
+ | ^ 2 | SD2_7_MUX_SEL | ||
+ | ^ 3 | SD3_MUX_SEL | ||
+ | ^ 4 | ENABLE_FAN | Fan disabled | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | ^ DIP ^ ON ^ OFF ^ | ||
+ | ^ 1 | EC2 Muxing | ||
+ | ^ 2 | --- | --- | | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | |||
+ |