This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong. ===== Starterkit Default DIP Switch Settings ===== By default the latest TQMLX2160A BSP has the following SerDes configuration: <grid> <col sm="4"> <panel type="primary" title="BSP default SerDes Configuration" no-body="true"> ^ SerDes module ^ SerDes protocol ^ | 1 | 14 | | 2 | 11 | | 3 | 2 | </panel> </col> </grid> Depending on the standard BSP SerDes configuration and boot source, the DIP switches must be configured as shown below: ==== SD Card ==== <grid> <col sm="2"> <panel type="primary" title="S1"> <WRAP centeralign> {{ :en:dip_4_1000.png?nolink&150 |}} </WRAP> </panel> </col> <col sm="2"> <panel type="primary" title="S2"> <WRAP centeralign> {{ :en:dip_4_1100.png?nolink&150 |}} </WRAP> </panel> </col> <col sm="2"> <panel type="primary" title="S3"> <WRAP centeralign> {{ :en:dip_4_1111.png?nolink&150 |}} </WRAP> </panel> </col> <col sm="2"> <panel type="primary" title="S4"> <WRAP centeralign> {{ :en:dip_4_0010.png?nolink&150 |}} </WRAP> </panel> </col> <col sm="2"> <panel type="primary" title="S5"> <WRAP centeralign> {{ :en:dip_2_10.png?nolink&85 |}} </WRAP> </panel> </col> </grid> ==== QSPI NOR ==== <grid> <col sm="2"> <panel type="primary" title="S1"> <WRAP centeralign> {{ :en:dip_4_0000.png?nolink&150 |}} </WRAP> </panel> </col> <col sm="2"> <panel type="primary" title="S2"> <WRAP centeralign> {{ :en:dip_4_1100.png?nolink&150 |}} </WRAP> </panel> </col> <col sm="2"> <panel type="primary" title="S3"> <WRAP centeralign> {{ :en:dip_4_1111.png?nolink&150 |}} </WRAP> </panel> </col> <col sm="2"> <panel type="primary" title="S4"> <WRAP centeralign> {{ :en:dip_4_0010.png?nolink&150 |}} </WRAP> </panel> </col> <col sm="2"> <panel type="primary" title="S5"> <WRAP centeralign> {{ :en:dip_2_10.png?nolink&85 |}} </WRAP> </panel> </col> </grid> ===== Starterkit Boot Source DIP Switch Settings ===== <grid> <col sm="4"> <panel type="primary" title="SD-Card"> <WRAP centeralign> [size=150%]**S1**[/size] {{ :en:dip_4_100x.png?nolink&150 |}} </WRAP> </panel> </col> <col sm="4"> <panel type="primary" title="eMMC"> <WRAP centeralign> [size=150%]**S1**[/size] {{ :en:dip_4_010x.png?nolink&150 |}} </WRAP> </panel> </col> <col sm="4"> <panel type="primary" title="NOR Flash"> <WRAP centeralign> [size=150%]**S1**[/size] {{ :en:dip_4_000x.png?nolink&150 |}} </WRAP> </panel> </col> </grid> ==== MBLx2160A Configuration DIP (S1,S2,S3,S4, S5) ==== <grid> <col sm="6"> <panel type="primary" title="S1" no-body="true"> ^ DIP ^ Function ^ ^ 1 | BOOT_SRC0 | ^ 2 | BOOT_SRC1 | ^ 3 | BOOT_SRC2 | ^ 4 | NOR_SWAP# | </panel> </col> </grid> <grid> <col sm="6"> <panel type="primary" title="S2" no-body="true"> ^ DIP ^ Function ^ ^ 1 | EMMC_SEL0 | ^ 2 | EMMC_SEL1 | ^ 3 | EVDD_SEL | ^ 4 | LX_CONIG_RFU1 | </panel> </col> <col sm="6"> <panel type="primary" title="S2: EMMC_SEL[0,1]" no-body="true"> ^ Function ^ EMMC_SEL0 ^ EMMC_SEL1 ^ | 8Bit eMMC | OFF | OFF | | 4Bit eMMC + 2x I²C | OFF | ON | | undefined | ON | OFF | | SDHC2 on Module Connector | ON | ON | </panel> </col> </grid> <grid> <col sm="6"> <panel type="primary" title="S3" no-body="true"> ^ DIP ^ Function ^ ON ^ OFF ^ ^ 1 | SD1_MUX_SEL | SGMII | PCIe | ^ 2 | SD2_2_MUX_SE | SGMII | SATA | ^ 3 | SD2_3_MUX_SEL | SGMII | SATA | ^ 4 | SD2_4_MUX_SEL | mPCIe | SATA | </panel> </col> <col sm="6"> <panel type="primary" title="S4" no-body="true"> ^ DIP ^ Function ^ ON ^ OFF ^ ^ 1 | SD2_6_MUX_SEL | XFI | SGMII | ^ 2 | SD2_7_MUX_SEL | XFI | SGMII | ^ 3 | SD3_MUX_SEL | PCIe x8 (X37) | 2x PCIe x4 (X35, X36) | ^ 4 | ENABLE_FAN | Fan disabled | Fan enabled | </panel> </col> </grid> <grid> <col sm="6"> <panel type="primary" title="S5" no-body="true"> ^ DIP ^ ON ^ OFF ^ ^ 1 | EC2 Muxing | EC2 1588 Muxing | ^ 2 | --- | --- | </panel> </col> </grid> Last modified: 2023/02/14 15:37