BIOS Overview

BIOS Revision TXE Firmware Version PCI Configurations BIOS Binary
Rev. 0105 5.12.30.28.07 3.1.65.2317 4×1 PCIe Lanes TQMxE39S_5.12.30.28.07.bin
Rev. 0104 5.12.30.21.06 3.1.50.2238 4×1 PCIe Lanes TQMxE39S_5.12.30.21.06.bin
1×4 PCIe Lanes TQMxE39S_5.12.30.21.06_PCIe_1x4.bin
1×2 + 2×1 PCIe Lanes TQMxE39S_5.12.30.21.06_PCIe_1x22x1.bin
Rev. 0103 5.12.30.21.05 3.1.50.2238 4×1 PCIe Lanes TQMxE39S_5.12.30.21.05.bin
1×4 PCIe Lanes TQMxE39S_5.12.30.21.05_PCIe_1x4.bin
1×2 + 2×1 PCIe Lanes TQMxE39S_5.12.30.21.05_PCIe_1x22x1.bin
Rev. 0102 5.12.30.21.04 3.1.50.2238 4×1 PCIe Lanes TQMxE39S_5.12.30.21.04.bin
1×4 PCIe Lanes TQMxE39S_5.12.30.21.04_PCIe_1x4.bin
1×2 + 2×1 PCIe Lanes TQMxE39S_5.12.30.21.04_PCIe_1x22x1.bin
Rev. 0101 5.12.09.16.03 3.1.50.2222 4×1 PCIe Lanes TQMxE39S_5.12.09.16.03.bin
Rev. 0100 5.12.09.16.02 3.1.50.2222 4×1 PCIe Lanes TQMxE39S_5.12.09.16.02.bin
1×4 PCIe Lanes TQMxE39S_5.12.09.16.02_PCIe_1x4.bin
1×2 + 2×1 PCIe Lanes TQMxE39S_5.12.09.16.02_PCIe_1x22x1.bin

Changelog

5.12.30.28.07

  • Insyde core update to tag_05.12.30.0028
    • Update SIC code to 1.1.1
    • improve realtime behavior

5.12.30.21.06

  • Adapt setup menu
    • Unhide power limits
    • Unhide DCI Enable
  • USB Device functionality
    • Unhide XDCI Support
    • Adapt Strings of xDCI for better understanding

5.12.30.21.05

  • Add Smart Battery Switch in BIOS Menu
  • Support F1-Stepping
    • Update PMC Version
    • Update Microcode
    • Update SIC Version
  • Update GPIO configuration to fix SD-Card functionality
  • Add Line In for Audio Code (MB-SMARC carrier)
  • Switch SMBIOS data from debug to release version

5.12.30.21.04

  • Adapt GPIO configuration to increase longevity of CPU GPIOs
  • Fix not booting system if UartPostCodeSupport disabled
  • Integrate 16Gb one rank memory configuration
  • Integrate 8Gb memory chip configuration
  • Enable Minimum Refresh Rate 2x
  • Core update to tag_05.12.30.0021
    • Close security gap spectre variant 2, 3a and 4
    • Fix 'State after G3' issue
    • Fix USB 3.0 not working
  • Adapt setup default configuration
    • USB Per-Port Control <enabled>
  • Adapt setup menu
    • Unhide “OS Reset Select”
    • Hide “BIOS Boot Source” information
  • Fix H2OUVE default bug of LFP configuration
  • Integrate MRC patch to fix ECC issue (stop booting with postcode 30)
  • Use old InsydeCrPkg to fix boot stop with postcode 0x0C84 or 0x004D
  • Fix not working SPI flash GD 25LQ128D
  • Support coinless Apl-I BIOS
  • Support Smart Battery
    • Integrate Smart Battery Switch in SCU

5.12.09.16.03

  • Integrate 8Gb memory chip configuration
  • Correct GPIO adress

5.12.09.16.02

  • Adapt setup menu (hide many entries)
  • Update setup defaults to the TQMxE39S
  • Correct LVDS resolutions in SioTqmx86 driver
  • Configure GPI interrupt as level-triggered
  • Add menu to enable GPI interrupt IRQ12
  • Add and adapt new TXE FW 3.1.50.2222
  • Fix wrong negative temperature
  • Adapt temperature string
  • Enable all PCIe roots
  • Enable RTS/CTS in SioTqmx86 driver
  • Identify two or four chip memory configuration
  • Fix missing memory channels in SCU
  • CPU to DRAM mapping for LPDDR4
  • Fix not working HSUARTS as COM Ports
  • Fix not working Over Current on USB0
  • Fix not working USB3 after integrate TXE
  • Unhide “HDMI/DVI” to use 4K monitors
  • Fix not working SPI Flash GD 25LQ128D
  • Disable UART Postcode support