Differences

This shows you the differences between two versions of the page.

--- en:arm:tqma28:mba28:dip_switches [2020/10/26 10:57] – new design (Temp) weinholdo
+++ en:arm:tqma28:mba28:dip_switches [2020/10/26 11:26] – weinholdo
@@ Line 4: / Line 4: @@
 <callout type="warning">
-It is not possible to boot from SD card with the following Hardware combination TQMa28-A[C,D,E] Rev.02XX and MBa28 ≤ Rev.0105. please goto [[#workaround_sd-card_boot| test]]
+It is not possible to boot from SD card with the following Hardware combination TQMa28-A[C,D,E] Rev.02XX and MBa28 ≤ Rev.0105. \\
+ [[#workaround_sd-card_boot| Click here for a workaround.]]
 </callout>
@@ Line 11: / Line 12: @@
 <grid>
-<col sm="6">
+<col sm="4">
 <panel type="primary" title="SD-Card">
@@ Line 34: / Line 35: @@
 </col>
-<col sm="6">
+<col sm="4">
 <panel type="primary" title="eMMC">
 <grid>
@@ Line 51: / Line 52: @@
 </WRAP>
 </col>
 </grid>
 </panel>
 </col>
-</grid>
+<col sm="4">
+<panel type="primary" title="USB Recovery">
+<grid>
+<col sm="6">
+<WRAP centeralign>
+[size=150%]**S4**[/size]
+{{ :en:dip_4_0100.png?nolink&180 |}}
+</WRAP>
+</col>
+<col sm="6">
-==== SD card ====
+<WRAP centeralign>
-^ |:::   ^  S4  ||||::: ^  S5  ||||
+[size=150%]**S5**[/size]
-^ |:::   ^  {{ :en:arm:tqma28:mba28:mba28_s4_sd.png?nolink&100 |}} ||||:::  ^ {{ :en:arm:tqma28:mba28:mba28_s5_sd.png?nolink&100 |}} ^^^^
+{{ :en:dip_4_100x.png?nolink&180 |}}
-^ DIP |::: ^  1  ^  2  ^  3  ^  4  | ::: ^  1  ^  2  ^  3  ^  4  ^
+S5-2: see User Manual, Table 69
-^ ON  | ::: |  |   |   |  •  | :::   |  •  | ++note| [[https://www.tq-group.com/content/download/12918/file/STK-MBa28.UM.104.pdf| see STK-MBa28 User's Manual, Table 69 ]] ++ |  •  | N/A  |
-^ OFF | ::: |  •  |  •  |  •  |     | :::  |   | :::   |   | :::  |
-\\
-<WRAP round important 80%> It is not possible to boot from SD card with the following Hardware combination TQMa28-A[C,D,E] Rev.02XX and MBa28 ≤ Rev.0105\\
-++++ for a workaround please click here !!! |
-Partlist
-{{ :en:arm:tqma28:mba28:mba28_mod.png?nolink&200|}}
-  * hookup wire
-  * 1k resistor
-TODO
-  * solder hookup wire from DIP S4-2 to DIP S5-3 (On is printed on the side of DIP switch)
-  * solder 1k resistor to Dip S5-3 (Number 3 is printed on the side of DIP switch)
-  * solder Connection between 1k resistor and the outer solder pad of R9
-  * set DIP S5-3 on
-++++
 </WRAP>
+</col>
+</grid>
+</panel>
+</col>
+</grid>
-----
+===== Functional DIP Switches =====
-==== On-board eMMC ====
+<panel type="primary" title="CAN configuration (S1)">
-^ |:::   ^  S4  ||||::: ^  S5  ||||:::
-^ |:::   ^  {{ :en:arm:tqma28:mba28:mba28_s4_emmc.png?nolink&100 |}} ||||:::  ^ {{ :en:arm:tqma28:mba28:mba28_s5_emmc.png?nolink&100 |}} ^^^^
-^ DIP |::: ^  1  ^  2  ^  3  ^  4  | ::: ^  1  ^  2  ^  3  ^  4  ^
-^ ON  | ::: |  |   |   |     | :::   |     | ++note| [[https://www.tq-group.com/content/download/12918/file/STK-MBa28.UM.104.pdf| see STK-MBa28 User's Manual, Table 69 ]] ++|     | N/A  |
-^ OFF | ::: |  •  |  •  |  •  |  •  | :::  |  •  | :::   |  •  | :::  |
-----
-==== USB Recovery ====
-^ |:::   ^  S4  ||||::: ^  S5  ||||
-^ |:::   ^  {{ :en:arm:tqma28:mba28:mba28_s4_recovery.png?nolink&100 |}} ||||:::  ^ {{ :en:arm:tqma28:mba28:mba28_s5_recovery.png?nolink&100 |}} ^^^^
-^ DIP |::: ^  1  ^  2  ^  3  ^  4  | ::: ^  1  ^  2  ^  3  ^  4  ^
-^ ON  | ::: |  |  •  |   |     | :::   |  •   | ++note| [[http://www.tq-group.com/nc/download-disclaimer/?tx_abdownloads_pi1%5Baction%5D=getviewclickeddownload&tx_abdownloads_pi1%5Buid%5D=1844&cHash=f4ba7c16e746568621463e9a02974cb2| see STK-MBa28 User's Manual, Table 69 ]] ++ |     | N/A  |
-^ OFF | ::: |  •  |     |  •  |  •  | :::  |   | :::   |  •  | :::  |
-----
-===== CAN configuration (S1) =====
 DIP switch S1 is used to configure the CAN interfaces CAN1 and CAN2.
-{{.:STK-MBa28_S1_overview.jpg?500  |}}
-==== Termination ====
-^ DIP  ^ OFF (default)  ^  ON  ^
-| S1-1 | CAN1 terminated (120Ω)  | CAN1 not terminated  |
-| S1-2 | CAN2 terminated (120Ω)  | CAN2 not terminated  |
-==== Slew rate ====
 ^ DIP  ^ OFF (default)  ^  ON  ^
+| S1-1 | CAN1 not terminated  | CAN1 terminated (120Ω)  |
+| S1-2 | CAN2 not terminated  | CAN2 terminated (120Ω)  |
 | S1-3 | CAN1 slew rate configuration disabled  | CAN1 slew rate configurable by assembling R282  |
 | S1-4 | CAN2 slew rate configuration disabled  | CAN2 slew rate configurable by assembling R281  |
+</panel>
+<panel type="primary" title="RS485 configuration (S3)">
-----
-===== RS485 configuration (S3) =====
 DIP switch S3 is used to configure the RS485 interface.
+^  DIP  ^  OFF (default)  ^  ON  ^
-{{.:STK-MBa28_S3_overview.jpg?500  |}}
+|  S3-1  | No function  | No function  |
+|  S3-2  | DEBUG = GND  | DEBUG = TQMa28 PU  |
+|  S3-3  | RS485 RxD terminated (120Ω)  | RS485 RxD not terminated   |
-==== Debug====
+|  S3-4  | RS485 TxD terminated (120Ω)  | RS485 TxD not terminated   |
-^ DIP  ^ OFF (default)  ^  ON  ^
+</panel>
-| S3-1 | No function  | No function  |
-| S3-2 | DEBUG = GND  | DEBUG = TQMa28 PU  |
-==== Termination ====
-^ DIP  ^ OFF (default)  ^  ON  ^
-| S3-3 | RS485 RxD terminated (120Ω)  | RS485 RxD not terminated  |
-| S3-4 | RS485 TxD terminated (120Ω)  | RS485 TxD not terminated  |