Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
en:arm:tqma335x:mba335x:dip_switches [2014/07/18 12:45] – created liedmann | en:arm:tqma335x:mba335x:dip_switches [2022/08/04 15:02] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | content | + | |
+ | ====== MBa335x DIP switch settings ====== | ||
+ | |||
+ | ===== Boot Device Selection (S2) ===== | ||
+ | |||
+ | To select the desired boot order set the DIP switch S2 accordingly. | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | The following boot sequences of the AM335x can be selected by the DIP switch S2 on the MBa335x. | ||
+ | Each boot device | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S2**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S2**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | < | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S2**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | </ | ||
+ | |||
+ | |||
+ | ===== CPU oscillator frequency configuration (S1) ===== | ||
+ | |||
+ | DIP switch S1-7 and S1-8 are used to configure the CPU oscillator frequency. | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S1**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S1**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S1**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S1**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | ===== Functional DIP Switches ===== | ||
+ | DIP-Switch settings for CAN and RS485. | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | DIP switch S3 is used to configure the CAN interfaces CAN1 and CAN2. | ||
+ | ^ DIP ^ OFF (default) | ||
+ | | S3-1 | CAN1 not terminated | ||
+ | | S3-2 | CAN2 not terminated | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | DIP switch S4 is used to configure the RS485 interface. | ||
+ | ^ DIP ^ OFF (default) | ||
+ | | S4-1 | RS485 RxD not terminated | ||
+ | | S4-2 | RS485 TxD not terminated | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | </ | ||
+ | |||
+ | ---- |