Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revisionLast revisionBoth sides next revision | ||
en:arm:tqma57xx:mba57xx:dip_switches [2020/08/25 11:56] – weinholdo | en:arm:tqma57xx:mba57xx:dip_switches [2020/10/20 14:14] – dip switch panels in grid weinholdo | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | <WRAP round important> **Work in Progress**</WRAP> | + | <alert type=" |
- | ====== MBa57xx DIP switch settings ====== | ||
===== Boot Device Selection (S1, S2) ===== | ===== Boot Device Selection (S1, S2) ===== | ||
- | To select the desired boot medium set the DIP switches S1 and S2 accordingly. | + | To select the desired boot medium set the DIP switches S1 and S2 accordingly. \\ |
+ | The following boot modes of the AM57XX can be selected by the DIP switches S1 and S2 on the MBa57xx. | ||
- | <WRAP clear></WRAP> | + | ---- |
- | The following boot modes of the AM57XX can be selected by the DIP switches S1 and S2 on the MBa57xx. | + | <grid> |
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | < | ||
+ | <col sm=" | ||
<WRAP centeralign> | <WRAP centeralign> | ||
- | ==== SD Card ==== | + | [size=150%]**S1**[/size] |
- | ^ |::: ^ | + | {{ :en:dip_8_10000001.png? |
- | ^ |::: ^ {{ :en:arm: | + | </ |
- | ^ DIP |::: ^ 1 ^ 2 ^ 3 ^ 4 ^ 5 ^ 6 ^ 7 ^ 8 | ::: ^ 1 ^ 2 ^ 3 ^ 4 ^ 5 ^ 6 ^ 7 ^ 8 | | + | </ |
- | ^ ON | + | |
- | ^ OFF |:::| |•|•|•|•|•|•| |::: | + | |
- | + | ||
- | ==== eMMC ==== | + | |
- | ^ |::: ^ S1 ||||||||::: ^ S2 |||||||| | + | |
- | ^ |::: ^ {{ : | + | |
- | ^ DIP |::: ^ 1 ^ 2 ^ 3 ^ 4 ^ 5 ^ 6 ^ 7 ^ 8 | ::: ^ 1 ^ 2 ^ 3 ^ 4 ^ 5 ^ 6 ^ 7 ^ 8 | | + | |
- | ^ ON | + | |
- | ^ OFF |:::| |•|•|•|•|•|•| |::: | + | |
- | ==== QSPI NOR ==== | + | <col sm=" |
- | ^ |::: ^ S1 ||||||||::: ^ | + | <WRAP centeralign> |
- | ^ |::: ^ {{ :en:arm: | + | [size=150%]**S2**[/size] |
- | ^ DIP |::: ^ 1 ^ 2 ^ 3 ^ 4 ^ 5 ^ 6 ^ 7 ^ 8 | ::: ^ 1 ^ 2 ^ 3 ^ 4 ^ 5 ^ 6 ^ 7 ^ 8 | | + | {{ :en:dip_8_00110000.png? |
- | ^ ON | + | |
- | ^ OFF |:::| |•|•|•|•|•|•| |::: | + | |
</ | </ | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
- | ---- | + | <col sm=" |
- | ===== CAN configuration (S3 / S7) ===== | + | |
- | DIP switch S3 is used to configure the CAN interfaces CAN1 and CAN2. | + | |
- | <WRAP>Both switches must be set to **ON** or **OFF** otherwise the CAN Bus has an improper termination.</ | + | <panel type=" |
- | \\ | + | |
- | <WRAP group> | + | |
- | <WRAP centeralign half column> | + | |
- | ^ DIP ^ S3-1/ | + | |
- | | ON | CAN Bus not terminated | + | |
- | | OFF (default) | + | |
+ | < | ||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S1**[/ | ||
+ | {{ : | ||
</ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S2**[/ | ||
+ | {{ : | ||
</ | </ | ||
- | <WRAP clear></WRAP> | + | </col> |
+ | </grid> | ||
+ | </panel> | ||
+ | </ | ||
+ | <col sm=" | ||
- | ---- | + | <panel type=" |
- | ===== RS485 configuration (S5) ===== | + | |
- | DIP switch S5 is used to configure the RS485 interface. | + | |
- | \\ | + | |
- | <WRAP group> | + | |
- | <WRAP half column> | + | |
- | ^ DIP ^ OFF (default) | + | < |
- | | S5-1 | RS485 TxD not terminated | + | <col sm=" |
- | | S5-2 | RS485 RxD not terminated | + | < |
- | + | [size=150%]**S1**[/ | |
- | </WRAP> | + | {{ : |
</ | </ | ||
- | <WRAP clear></WRAP> | + | </col> |
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S2**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | ===== Functional DIP Switches ===== | ||
+ | DIP-Switch settings for interfaces like JTAG, RS485 and CAN. | ||
---- | ---- | ||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | DIP switch S3 is used to configure the CAN interface CAN1. \\ | ||
+ | Both switches must be set to **ON** or **OFF** otherwise the CAN Bus has an improper termination. | ||
+ | ^ DIP ^ S3-1 & S3-2 | | ||
+ | ^ ON | CAN Bus not terminated | ||
+ | ^ OFF (default) | ||
+ | </ | ||
+ | </ | ||
- | ===== JTAG configuration | + | <col sm=" |
- | DIP switch | + | <panel type=" |
- | \\ | + | DIP switch |
- | <WRAP group> | + | Both switches must be set to **ON** or **OFF** otherwise the CAN Bus has an improper termination. |
- | <WRAP centeralign half column> | + | ^ DIP ^ S7-1 & S7-2 | |
+ | ^ ON | CAN Bus not terminated | ||
+ | ^ OFF (default) | ||
+ | </ | ||
+ | </col> | ||
+ | </grid> | ||
- | ^ DIP ^ OFF ^ ON ^ | ||
- | | S5-1 | JTAG via Micro-USB (x10) | JTAG via connector X11 | | ||
- | </WRAP> | + | < |
- | </WRAP> | + | <col sm=" |
- | <WRAP clear></WRAP> | + | |
+ | |||
+ | <panel type=" | ||
+ | DIP switch S5 is used to configure the RS485 interface. \\ | ||
+ | |||
+ | ^ DIP ^ S5-1 ^ S5-2 | | ||
+ | ^ ON | RS485 TxD terminated (120Ω) | ||
+ | ^ OFF (default) | ||
+ | |||
+ | </panel> | ||
+ | </col> | ||
+ | <col sm=" | ||
+ | |||
+ | |||
+ | |||
+ | <panel type=" | ||
+ | DIP switch S13 is used to configure the JTAG interface. \\ | ||
+ | |||
+ | ^ DIP ^ S13 | | ||
+ | ^ ON | JTAG via connector X11 | | ||
+ | ^ OFF | JTAG via Micro-USB (x10) | | ||
+ | |||
+ | </panel> | ||
+ | </ | ||
+ | </ | ||
+ |