Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
en:arm:tqma6x:mba6x:dip_switches [2014/07/18 12:44] – created liedmann | en:arm:tqma6x:mba6x:dip_switches [2022/08/04 15:02] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | content in progress | + | |
+ | ===== Boot Device Selection (S1, S2, S4 & S5) ===== | ||
+ | To select the desired boot medium set the DIP switches S1, S2, S4 and S5 accordingly. | ||
+ | |||
+ | <callout type=" | ||
+ | |||
+ | To enable boot device selection BOOT_MODE has to be set to " | ||
+ | S5 on MBa6x: | ||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | ^ BOOT_MODE | ||
+ | | Boot from eFuses | ||
+ | | Serial Downloader | 0 | ||
+ | | Internal Boot | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <callout type=" | ||
+ | Because of the SD/MMC Manufacture Mode of i.MX6 Solo (TQMa6S) and DualLite (TQMa6U), | ||
+ | please remove the SD Card from the Starterkit. Otherwise the Starterkit will boot from SD Card although " | ||
+ | \\ | ||
+ | \\ | ||
+ | For further information please see i.MX6 Solo and DualLite reference Manual chapter 8.11 SD/MMC Manufacture Mode | ||
+ | </ | ||
+ | |||
+ | <WRAP clear></ | ||
+ | The following boot modes of the i.MX6 can be selected by the DIP switches S1, S2, S4 and S5 on the MBa6x. | ||
+ | |||
+ | |||
+ | <panel type=" | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S1**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S2**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S4**[/ | ||
+ | {{ : | ||
+ | S4 has no effect | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S5**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | \\ | ||
+ | ---- | ||
+ | </ | ||
+ | |||
+ | <panel type=" | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S1**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | |||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S2**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S4**[/ | ||
+ | {{ : | ||
+ | S4 has no effect | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S5**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | \\ | ||
+ | ---- | ||
+ | </ | ||
+ | |||
+ | <panel type=" | ||
+ | < | ||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S1**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | |||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S2**[/ | ||
+ | {{ : | ||
+ | S2 has no effect | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S4**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S5**[/ | ||
+ | {{ : | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | \\ | ||
+ | ---- | ||
+ | </ | ||
+ | |||
+ | |||
+ | ===== Functional DIP Switches ===== | ||
+ | DIP-Switch settings for CAN and RS485. | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | DIP switch S13 is used to configure the CAN interfaces CAN1 and CAN2. | ||
+ | ^ DIP ^ OFF (default) | ||
+ | | S13-1 | CAN0 not terminated | ||
+ | | S13-2 | CAN1 not terminated | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | DIP switch S14 is used to configure the RS485 interface. | ||
+ | ^ DIP ^ OFF (default) | ||
+ | | S14-1 | RS485 RxD not terminated | ||
+ | | S14-2 | RS485 TxD not terminated | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | </ | ||
+ | |||
+ | ---- |