Differences

This shows you the differences between two versions of the page.

--- en:arm:tqma6x:mba6x:dip_switches [2014/08/07 13:25] – liedmann
+++ en:arm:tqma6x:mba6x:dip_switches [2022/08/04 15:02] (current) – external edit 127.0.0.1
@@ Line 3: / Line 3: @@
 To select the desired boot medium set the DIP switches S1, S2, S4 and S5 accordingly.
-<WRAP round important 60%>Switching boot sources is only possible if the BOOT_MODE fuses are not programmed. If configured for "Boot from eFuses" but fuses are not programmed, the boot loader will not be able to determine the boot source. </WRAP>
+<callout type="warning" icon="true">Switching boot sources is only possible if the BOOT_MODE fuses are not programmed.\\  If configured for "Boot from eFuses" but fuses are not programmed, the boot loader will not be able to determine the boot source.</callout>
 To enable boot device selection BOOT_MODE has to be set to "Internal Boot".\\ This can be done using DIP switch
 S5 on MBa6x:
+<grid>
-^ BOOT_MODE         ^ S5-1 ^ S5-2 ^
+<col sm="6">
+<panel type="default" title="Boot Modes" no-body="true">
+^ BOOT_MODE         ^  S5-1  ^  S5-2  ^
 | Boot from eFuses  |  0   |  0   |
 | Serial Downloader |  0   |  1   |
 | Internal Boot     |  1   |  0   |
+</panel>
+</col>
+</grid>
-{{:en:arm:tqma6x:mba6x:mba6x_s5.jpg?500|}}
+<callout type="warning" icon="true">
-{{:en:arm:tqma6x:mba6x:mba6x_s1-s4.jpg?nolink&500|}}
+Because of the SD/MMC Manufacture Mode of i.MX6 Solo (TQMa6S) and DualLite (TQMa6U),
+please remove the SD Card from the Starterkit. Otherwise the Starterkit will boot from SD Card although "serial Downloader" mode is set on DIP S5.
+\\
+\\
+For further information please see i.MX6 Solo and DualLite reference Manual chapter 8.11 SD/MMC Manufacture Mode
+</callout>
 <WRAP clear></WRAP>
@@ Line 22: / Line 30: @@
+<panel type="primary" title="SD-Card">
+<grid>
+<col sm="3">
 <WRAP centeralign>
-==== SD card ====
+[size=150%]**S1**[/size]
-^ |:::  ^  S1  ||||||||::: ^  S2  ||||||||::: ^  S4  ||||||||::: ^ S5  ||
+{{ :en:dip_8_01010000.png?nolink&270 |}}
-^ |:::  ^ {{ :en:arm:tqma6x:mba6x:mba6x_s1_sd.png?nolink&100 |}}||||||||:::  ^{{ :en:arm:tqma6x:mba6x:mba6x_s2_sd.png?nolink&100 |}}||||||||::: ^{{ :en:arm:tqma6x:mba6x:mba6x_s4_sd_grau.png?nolink&100 |}}||||||||:::  ^{{ :en:arm:tqma6x:mba6x:mba6x_s5_1on.png?nolink&35 |}}^^
-^  DIP  |::: ^  1  ^  2  ^  3  ^  4  ^  5  ^  6  ^  7  ^  8  | :::  ^  1  ^  2  ^  3  ^  4  ^  5  ^  6  ^  7  ^  8  | ::: ^ 1 ^  2  ^  3  ^  4  ^  5  ^  6  ^  7  ^  8  |:::^  1  ^  2  ^
-^  ON  |:::  | | • |  |  •  | | | | | ::: | | |  •  | |  •  | | | |:::^ ^ ^ ^ ^ ^ ^ ^  |:::| • | |
-^  OFF  |::: | • | | • |  | • | • | • | • | ::: | • |  •  |  |  •  | | • | • | • |:::^ ^ ^ ^ ^ ^ ^ ^ |:::| | • |
 </WRAP>
+</col>
+<col sm="3">
+<WRAP centeralign>
+[size=150%]**S2**[/size]
+{{ :en:dip_8_00101000.png?nolink&270 |}}
+</WRAP>
+</col>
+<col sm="3">
+<WRAP centeralign>
+[size=150%]**S4**[/size]
+{{ :en:dip_8_xxxxxxxx.png?nolink&270 |}}
+S4 has no effect
+</WRAP>
+</col>
+<col sm="3">
 <WRAP centeralign>
-==== eMMC ====
+[size=150%]**S5**[/size]
-^ |::: ^  S1  ||||||||::: ^  S2  ||||||||::: ^  S4  ||||||||::: ^  S5  ||
+{{ :en:dip_2_10.png?nolink&85 |}}
-^ |::: ^{{ :en:arm:tqma6x:mba6x:mba6x_s1_emmc.png?nolink&100 |}}||||||||:::  ^{{ :en:arm:tqma6x:mba6x:mba6x_s2_emmc.png?nolink&100 |}}||||||||:::  ^{{ :en:arm:tqma6x:mba6x:mba6x_s4_emmc_grau.png?nolink&100 |}}||||||||::: ^{{  :en:arm:tqma6x:mba6x:mba6x_s5_1on.png?nolink&35  |}}^^
-^  DIP  |::: ^  1  ^  2  ^  3  ^  4  ^  5  ^  6  ^  7  ^  8  | :::  ^  1  ^  2  ^  3  ^  4  ^  5  ^  6  ^  7  ^  8  | ::: ^ 1 ^  2  ^  3  ^  4  ^  5  ^  6  ^  7  ^  8  |:::^  1  ^  2  ^
-^  ON  |:::  | | • | • | | | | | | ::: | | • | | • | | | | |:::^ ^ ^ ^ ^ ^ ^ ^  |:::| • | |
-^  OFF  |::: | • | | | • | • | • | • | • | ::: | • | | • | | • | • | • | • |:::^ ^ ^ ^ ^ ^ ^ ^ |:::| | • |
 </WRAP>
+</col>
+</grid>
+\\
+----
+</panel>
+<panel type="primary" title="eMMC">
+<grid>
+<col sm="3">
 <WRAP centeralign>
-==== SPI-NOR ====
+[size=150%]**S1**[/size]
-^ |:::  ^  S1  ||||||||::: ^  S2  ||||||||::: ^  S4  ||||||||::: ^  S5  ||
+{{ :en:dip_8_01100000.png?nolink&270 |}}
-^ |:::  ^{{ :en:arm:tqma6x:mba6x:mba6x_s1_spi.png?nolink&100 |}}||||||||:::  ^{{ :en:arm:tqma6x:mba6x:mba6x_s2_spi_grau.png?nolink&100 |}}||||||||:::^ {{ :en:arm:tqma6x:mba6x:mba6x_s4_spi.png?nolink&100 |}}||||||||:::  ^ {{ :en:arm:tqma6x:mba6x:mba6x_s5_1on.png?nolink&35 |}}^^
-^  DIP  |::: ^  1  ^  2  ^  3  ^  4  ^  5  ^  6  ^  7  ^  8  | :::  ^  1  ^  2  ^  3  ^  4  ^  5  ^  6  ^  7  ^  8  | ::: ^ 1 ^  2  ^  3  ^  4  ^  5  ^  6  ^  7  ^  8  |:::^  1  ^  2  ^
-^  ON  |:::  | | |  •  |  •  | | | | | :::^ ^ ^ ^ ^ ^ ^ ^ |::: | | |  |  •  |  •  | | |  |:::| • | |
-^  OFF  |::: | • |  •  | | | • | • | • | • | :::^ ^ ^ ^ ^ ^ ^ ^ |::: | • |  •  |  •  | |  | • | • | • |:::| | • |
 </WRAP>
+</col>
-----
+<col sm="3">
-===== CAN configuration (S13) =====
+<WRAP centeralign>
-DIP switch S13 is used to configure the CAN interfaces CAN1 and CAN2.
+[size=150%]**S2**[/size]
+{{ :en:dip_8_01010000.png?nolink&270 |}}
+</WRAP>
+</col>
-{{:en:arm:tqma6x:mba6x:mba6x_s13_can.jpg?nolink&500 |}}
+<col sm="3">
+<WRAP centeralign>
+[size=150%]**S4**[/size]
+{{ :en:dip_8_xxxxxxxx.png?nolink&270 |}}
+S4 has no effect
+</WRAP>
+</col>
-<WRAP group>
+<col sm="3">
-<WRAP centeralign half column>
+<WRAP centeralign>
-==== Termination ====
+[size=150%]**S5**[/size]
-^ DIP  ^ OFF (default)  ^  ON  ^
+{{ :en:dip_2_10.png?nolink&85 |}}
-| S13-1 |  CAN0 not terminated  | CAN0 terminated (120Ω) |
-| S13-2 |  CAN1 not terminated  | CAN1 terminated (120Ω) |
 </WRAP>
-<WRAP clear></WRAP>
+</col>
+</grid>
+\\
 ----
-===== RS485 configuration (S14) =====
+</panel>
-DIP switch S14 is used to configure the RS485 interface.
-{{:en:arm:tqma6x:mba6x:mba6x_s14_rs485.jpg?nolink&500 |}}
+<panel type="primary" title="SPI NOR">
+<grid>
+<col sm="3">
+<WRAP centeralign>
+[size=150%]**S1**[/size]
+{{ :en:dip_8_00110000.png?nolink&270 |}}
+</WRAP>
+</col>
-<WRAP clear></WRAP>
-<WRAP group>
+<col sm="3">
+<WRAP centeralign>
+[size=150%]**S2**[/size]
+{{ :en:dip_8_xxxxxxxx.png?nolink&270 |}}
+S2 has no effect
 </WRAP>
-<WRAP centeralign half column>
+</col>
-==== Termination ====
-^ DIP  ^ OFF (default)  ^  ON  ^
+<col sm="3">
-| S14-1 |  RS485 RxD not terminated  | RS485 RxD terminated (120Ω) |
+<WRAP centeralign>
-| S14-2 |  RS485 TxD not terminated  | RS485 TxD terminated (120Ω) |
+[size=150%]**S4**[/size]
+{{ :en:dip_8_00011000.png?nolink&270 |}}
 </WRAP>
+</col>
+<col sm="3">
+<WRAP centeralign>
+[size=150%]**S5**[/size]
+{{ :en:dip_2_10.png?nolink&85 |}}
 </WRAP>
+</col>
+</grid>
+\\
+----
+</panel>
+===== Functional DIP Switches =====
+DIP-Switch settings for CAN and RS485.
+<grid>
+<col sm="6">
+<panel type="primary" title="CAN configuration (S13)">
+DIP switch S13 is used to configure the CAN interfaces CAN1 and CAN2.
+^  DIP  ^  OFF (default)  ^  ON  ^
+|  S13-1  |  CAN0 not terminated  |  CAN0 interface terminated (120Ω)  |
+|  S13-2  |  CAN1 not terminated  |  CAN1 interface terminated (120Ω)  |
+</panel>
+</col>
+<col sm="6">
+<panel type="primary" title="RS485 configuration (S14)">
+DIP switch S14 is used to configure the RS485 interface.
+^  DIP  ^  OFF (default)  ^  ON  ^
+|  S14-1  |  RS485 RxD not terminated  |  RS485 RxD terminated (120Ω)  |
+|  S14-2  |  RS485 TxD not terminated  |  RS485 TxD terminated (120Ω)  |
+</panel>
+</col>
+</grid>
+----