Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision Next revisionBoth sides next revision | ||
en:arm:tqmls102xa:mbls102xa:dip_switches [2015/07/19 11:07] – created liedmann | en:layerscape:tqmls102xa:mbls102xa:dip_switches [2021/03/16 13:54] – change dip switch image weinholdo | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== MBLS102xA DIP switch settings ====== | + | ====== MBLS102xA DIP switch settings ====== |
+ | |||
+ | <alert type=" | ||
+ | |||
+ | ===== Boot Device Selection (S3) ===== | ||
+ | To select the desired boot medium set the DIP switches S3, S9 accordingly | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | |||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S3**[/ | ||
+ | {{ : | ||
+ | <alert type=" | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | |||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S3**[/ | ||
+ | {{ : | ||
+ | <alert type=" | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | </ | ||
+ | <col sm=" | ||
+ | |||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S3**[/ | ||
+ | {{ : | ||
+ | S3-2 ON: TQMLS102xA without eMMC \\ | ||
+ | S3-2 OFF: TQMLS102xA with eMMC | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== CPLD Function Selection (S9) ===== | ||
+ | \\ | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | ^ S9 ^ DIP 1 ^ DIP 2 ^ | ||
+ | ^ HDMI | ON | ON | | ||
+ | ^ LVDS | OFF | ON | | ||
+ | ^ UCC | ON | OFF | | ||
+ | ^ LVDS_RGBINV | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | ^ S9 ^ DIP 3 ^ DIP 4 ^ | ||
+ | ^ EC1 | ON | ON | | ||
+ | ^ CAN1 / CAN2 | OFF | ON | | ||
+ | ^ SAI1 / SAI2 | ON | OFF | | ||
+ | ^ Reserved | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <alert type=" | ||
+ | <callout type=" | ||
+ | CPLD mux mode #1 EC1_HDMI matches the default RCW configuration of the TQMLS102xA BSP.\\ | ||
+ | If DIP S9 is not set to one of the CPLD mux modes #1 - #12, the CPLD firmware selects mux mode #1. </ | ||
+ | |||
+ | < | ||
+ | ^ Function | ||
+ | ^ #1 EC1 + HDMI | ON | ON | ON | ON | | ||
+ | ^ #2 EC1 + LVDS | OFF | ON | ON | ON | | ||
+ | ^ #3 EC1 + UCC | ON | OFF | ON | ON | | ||
+ | ^ #4 EC1 + LVDS_RGBINV | ||
+ | ^ #5 CAN + HDMI | ON | ON | OFF | ON | | ||
+ | ^ #6 CAN + LVDS | OFF | ON | OFF | ON | | ||
+ | ^ #7 CAN + UCC | ON | OFF | OFF | ON | | ||
+ | ^ #8 CAN + LVDS_RGBINV | ||
+ | ^ #9 SAI + HDMI | ON | ON | ON | OFF | | ||
+ | ^ #10 SAI + LVDS | OFF | ON | ON | OFF | | ||
+ | ^ #11 SAI + UCC | ON | OFF | ON | OFF | | ||
+ | ^ #12 SAI + LVDS_RGBINV | ||
+ | ^ #13 - #16 reserved | ||
+ | </ | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== Functional DIP Switches ===== | ||
+ | DIP-Switch settings for CAN and RS485. | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | DIP switch S2 is used to configure the CAN interfaces CAN1 and CAN2. | ||
+ | ^ DIP ^ OFF (default) | ||
+ | | S2-1 | CAN0 not terminated | ||
+ | | S2-2 | CAN1 not terminated | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | DIP switch S1 is used to configure the RS485 interface. | ||
+ | ^ DIP ^ OFF (default) | ||
+ | | S1-1 | RS485 RxD not terminated | ||
+ | | S1-2 | RS485 TxD not terminated | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | </ | ||
+ | |||
+ | ---- |