Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
en:arm:tqmls102xa:mbls102xa:dip_switches [2016/06/27 16:14] – liedmann | en:layerscape:tqmls102xa:mbls102xa:dip_switches [2021/03/16 13:54] – change dip switch image weinholdo | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== MBLS102xA DIP switch settings ====== | + | ====== MBLS102xA DIP switch settings ====== |
- | <WRAP round important>WORK IN PROGRESS</WRAP> | + | <alert type=" |
===== Boot Device Selection (S3) ===== | ===== Boot Device Selection (S3) ===== | ||
- | To select the desired boot medium set the DIP switches S3 accordingly. | + | To select the desired boot medium set the DIP switches S3, S9 accordingly |
+ | < | ||
+ | <col sm=" | ||
- | ==== SD card ==== | + | <panel type=" |
- | ^ |::: ^ | + | <WRAP centeralign> |
- | ^ DIP |::: ^ 1 ^ 2 ^ 3 ^ 4 | + | [size=150%]**S3**[/size] |
- | ^ ON |:::| • | • ^ ^ ^ | + | {{ :en:dip_4_11xx.png? |
- | ^ OFF |:::| | ^ ^ ^ | + | <alert type=" |
- | \\ | + | </ |
+ | </ | ||
- | <WRAP round important 40%> eMMC is a placement option on TQMLS102xA</WRAP> | + | </col> |
- | ==== eMMC ==== | + | <col sm="4"> |
- | ^ |::: ^ S3 |||| | + | |
- | ^ DIP |::: ^ 1 ^ 2 ^ 3 ^ 4 | | + | |
- | ^ ON |:::| • | ^ ^ ^ | + | |
- | ^ OFF |:::| | • ^ ^ ^ | + | |
- | \\ | + | |
- | ==== QSPI ==== | + | |
- | ^ |::: ^ S3 |||| | + | |
- | ^ DIP |::: ^ 1 ^ 2 ^ 3 ^ | + | |
- | ^ ON |:::| ^ ^ ^ ^ | + | |
- | ^ OFF |:::| • ^ ^ ^ ^ | + | |
- | \\ | + | |
- | ===== CAN configuration (S2) ===== | + | <panel type=" |
- | DIP switch S2 is used to configure the CAN interfaces CAN0 and CAN1. | + | <WRAP centeralign> |
- | <WRAP centeralign | + | [size=150%]**S3**[/ |
- | ==== Termination ==== | + | {{ : |
- | ^ DIP ^ OFF (default) | + | <alert type=" |
- | | S2-1 | CAN0 not terminated | + | |
- | | S2-2 | CAN1 not terminated | + | |
</ | </ | ||
- | <WRAP clear></WRAP> | + | </panel> |
- | ===== RS485 configuration (S1) ===== | + | </ |
- | DIP switch S1 is used to configure the RS485 interface. | + | <col sm=" |
- | <WRAP centeralign | + | |
- | ==== Termination ==== | + | <panel type=" |
- | ^ DIP ^ OFF (default) | + | <WRAP centeralign> |
- | | S1-1 | RS485 RxD not terminated | + | [size=150%]**S3**[/ |
- | | S1-2 | RS485 TxD not terminated | + | {{ : |
+ | S3-2 ON: TQMLS102xA without eMMC \\ | ||
+ | S3-2 OFF: TQMLS102xA with eMMC | ||
</ | </ | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== CPLD Function Selection (S9) ===== | ||
+ | \\ | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | ^ S9 ^ DIP 1 ^ DIP 2 ^ | ||
+ | ^ HDMI | ON | ON | | ||
+ | ^ LVDS | OFF | ON | | ||
+ | ^ UCC | ON | OFF | | ||
+ | ^ LVDS_RGBINV | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | ^ S9 ^ DIP 3 ^ DIP 4 ^ | ||
+ | ^ EC1 | ON | ON | | ||
+ | ^ CAN1 / CAN2 | OFF | ON | | ||
+ | ^ SAI1 / SAI2 | ON | OFF | | ||
+ | ^ Reserved | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <alert type=" | ||
+ | <callout type=" | ||
+ | CPLD mux mode #1 EC1_HDMI matches the default RCW configuration of the TQMLS102xA BSP.\\ | ||
+ | If DIP S9 is not set to one of the CPLD mux modes #1 - #12, the CPLD firmware selects mux mode #1. </ | ||
+ | |||
+ | < | ||
+ | ^ Function | ||
+ | ^ #1 EC1 + HDMI | ON | ON | ON | ON | | ||
+ | ^ #2 EC1 + LVDS | OFF | ON | ON | ON | | ||
+ | ^ #3 EC1 + UCC | ON | OFF | ON | ON | | ||
+ | ^ #4 EC1 + LVDS_RGBINV | ||
+ | ^ #5 CAN + HDMI | ON | ON | OFF | ON | | ||
+ | ^ #6 CAN + LVDS | OFF | ON | OFF | ON | | ||
+ | ^ #7 CAN + UCC | ON | OFF | OFF | ON | | ||
+ | ^ #8 CAN + LVDS_RGBINV | ||
+ | ^ #9 SAI + HDMI | ON | ON | ON | OFF | | ||
+ | ^ #10 SAI + LVDS | OFF | ON | ON | OFF | | ||
+ | ^ #11 SAI + UCC | ON | OFF | ON | OFF | | ||
+ | ^ #12 SAI + LVDS_RGBINV | ||
+ | ^ #13 - #16 reserved | ||
+ | </ | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== Functional DIP Switches ===== | ||
+ | DIP-Switch settings for CAN and RS485. | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | DIP switch S2 is used to configure the CAN interfaces CAN1 and CAN2. | ||
+ | ^ DIP ^ OFF (default) | ||
+ | | S2-1 | CAN0 not terminated | ||
+ | | S2-2 | CAN1 not terminated | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | DIP switch S1 is used to configure the RS485 interface. | ||
+ | ^ DIP ^ OFF (default) | ||
+ | | S1-1 | RS485 RxD not terminated | ||
+ | | S1-2 | RS485 TxD not terminated | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | </ | ||
+ | ---- |