Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
en:arm:tqmls102xa:mbls102xa:dip_switches [2017/01/09 08:53] – added dip S9 info liedmann | en:layerscape:tqmls102xa:mbls102xa:dip_switches [2022/10/12 12:53] (current) – liedmann | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== MBLS102xA DIP switch settings ====== | + | ====== MBLS102xA DIP switch settings ====== |
- | <WRAP round important> | ||
===== Boot Device Selection (S3) ===== | ===== Boot Device Selection (S3) ===== | ||
- | To select the desired boot medium set the DIP switches S3 accordingly. | + | To select the desired boot medium set the DIP switches S3, S9 accordingly |
+ | < | ||
+ | <col sm=" | ||
+ | |||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S3**[/ | ||
+ | {{ : | ||
+ | <alert type=" | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | |||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S3**[/ | ||
+ | {{ : | ||
+ | <alert type=" | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | </ | ||
+ | <col sm=" | ||
+ | |||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S3**[/ | ||
+ | {{ : | ||
+ | S3-2 ON: TQMLS102xA without eMMC \\ | ||
+ | S3-2 OFF: TQMLS102xA with eMMC | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
- | ==== SD card ==== | ||
- | ^ |::: ^ S3 |||| | ||
- | ^ DIP |::: ^ 1 ^ 2 ^ 3 ^ 4 | | ||
- | ^ ON |:::| • | • ^ ^ ^ | ||
- | ^ OFF |:::| | ^ ^ ^ | ||
- | \\ | ||
- | <WRAP round important 40%> eMMC is a placement option on TQMLS102xA</ | ||
- | ==== eMMC ==== | ||
- | ^ |::: ^ S3 |||| | ||
- | ^ DIP |::: ^ 1 ^ 2 ^ 3 ^ 4 | | ||
- | ^ ON |:::| • | ^ ^ ^ | ||
- | ^ OFF |:::| | • ^ ^ ^ | ||
- | \\ | ||
- | ==== QSPI ==== | ||
- | ^ |::: ^ S3 |||| | ||
- | ^ DIP |::: ^ 1 ^ 2 ^ 3 ^ 4 | | ||
- | ^ ON |:::| ^ ^ ^ ^ | ||
- | ^ OFF |:::| • ^ ^ ^ ^ | ||
- | \\ | ||
===== CPLD Function Selection (S9) ===== | ===== CPLD Function Selection (S9) ===== | ||
\\ | \\ | ||
- | ==== S9 DIP switch 1 + 2 ==== | ||
- | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
^ S9 ^ DIP 1 ^ DIP 2 ^ | ^ S9 ^ DIP 1 ^ DIP 2 ^ | ||
^ HDMI | ON | ON | | ^ HDMI | ON | ON | | ||
Line 39: | Line 56: | ||
^ UCC | ON | OFF | | ^ UCC | ON | OFF | | ||
^ LVDS_RGBINV | ^ LVDS_RGBINV | ||
- | \\ | + | </ |
- | + | </ | |
- | + | ||
- | + | ||
- | ==== S9 DIP switch 3 + 4 ==== | + | |
- | ^ S9 ^ DIP 3 ^ DIP 4 ^ | + | <col sm=" |
+ | <panel type=" | ||
+ | ^ S9 ^ DIP 3 ^ DIP 4 ^ | ||
^ EC1 | ON | ON | | ^ EC1 | ON | ON | | ||
^ CAN1 / CAN2 | OFF | ON | | ^ CAN1 / CAN2 | OFF | ON | | ||
^ SAI1 / SAI2 | ON | OFF | | ^ SAI1 / SAI2 | ON | OFF | | ||
^ Reserved | ^ Reserved | ||
- | \\ | + | </ |
+ | </ | ||
+ | </ | ||
+ | <alert type=" | ||
+ | <callout type=" | ||
+ | CPLD mux mode #1 EC1_HDMI matches the default RCW configuration of the TQMLS102xA BSP.\\ | ||
+ | If DIP S9 is not set to one of the CPLD mux modes #1 - #12, the CPLD firmware selects mux mode #1. </ | ||
- | <WRAP round important> The settings of DIP S9 has to match the TQMLS102xA BSP RCW configuration.</WRAP> | + | <panel> |
+ | ^ Function | ||
+ | ^ #1 EC1 + HDMI | ON | ON | ON | ON | | ||
+ | ^ #2 EC1 + LVDS | OFF | ON | ON | ON | | ||
+ | ^ #3 EC1 + UCC | ON | OFF | ON | ON | | ||
+ | ^ #4 EC1 + LVDS_RGBINV | ||
+ | ^ #5 CAN + HDMI | ON | ON | OFF | ON | | ||
+ | ^ #6 CAN + LVDS | OFF | ON | OFF | ON | | ||
+ | ^ #7 CAN + UCC | ON | OFF | OFF | ON | | ||
+ | ^ #8 CAN + LVDS_RGBINV | ||
+ | ^ #9 SAI + HDMI | ON | ON | ON | OFF | | ||
+ | ^ #10 SAI + LVDS | OFF | ON | ON | OFF | | ||
+ | ^ #11 SAI + UCC | ON | OFF | ON | OFF | | ||
+ | ^ #12 SAI + LVDS_RGBINV | ||
+ | ^ #13 - #16 reserved | ||
+ | </panel> | ||
- | <WRAP round info> | ||
- | If DIP S9 is not set to one of the CPLD mux modes #1 - #12, the CPLD firmware selects mux mode #1. </ | ||
- | ^ Function | ||
- | ^ #1 EC1_HDMI | ||
- | ^ #2 EC1_LVDS | ||
- | ^ #3 EC1_UCC | ||
- | ^ #4 EC1_LVDS_RGBINV | ||
- | ^ #5 CAN_HDMI | ||
- | ^ #6 CAN_LVDS | ||
- | ^ #7 CAN_UCC | ||
- | ^ #8 CAN_LVDS_RGBINV | ||
- | ^ #9 SAI_HDMI | ||
- | ^ #10 SAI_LVDS | ||
- | ^ #11 SAI_LVDS | ||
- | ^ #12 SAI_LVDS_RGBINV | ||
- | ^ #13 - #16 reserved | ||
- | ===== CAN configuration (S2) ===== | + | ===== Functional DIP Switches |
- | DIP switch S2 is used to configure the CAN interfaces CAN0 and CAN1. | + | DIP-Switch settings for CAN and RS485. |
- | <WRAP centeralign half column> | + | |
- | ==== Termination ==== | + | |
- | ^ DIP ^ OFF (default) | + | |
- | | S2-1 | CAN0 not terminated | + | |
- | | S2-2 | CAN1 not terminated | + | |
- | </ | + | |
- | <WRAP clear></ | + | |
- | ===== RS485 configuration (S1) ===== | + | < |
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | DIP switch S2 is used to configure the CAN interfaces CAN1 and CAN2. | ||
+ | ^ DIP ^ OFF (default) | ||
+ | | S2-1 | CAN0 not terminated | ||
+ | | S2-2 | CAN1 not terminated | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
DIP switch S1 is used to configure the RS485 interface. | DIP switch S1 is used to configure the RS485 interface. | ||
- | <WRAP centeralign half column> | + | ^ DIP ^ OFF (default) |
- | ==== Termination ==== | + | | S1-1 | RS485 RxD not terminated |
- | ^ DIP ^ OFF (default) | + | | S1-2 | RS485 TxD not terminated |
- | | S1-1 | RS485 RxD not terminated | + | </panel> |
- | | S1-2 | RS485 TxD not terminated | + | </ |
- | </WRAP> | + | |
+ | </grid> | ||
+ | ---- |