Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
en:arm:tqmls102xa:mbls102xa:dip_switches [2017/08/25 10:39] – Pictures Boot Device Selection schmid | en:layerscape:tqmls102xa:mbls102xa:dip_switches [2021/03/16 13:54] – change dip switch image weinholdo | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== MBLS102xA DIP switch settings ====== | ====== MBLS102xA DIP switch settings ====== | ||
- | <WRAP round important>WORK IN PROGRESS</WRAP> | + | <alert type=" |
===== Boot Device Selection (S3) ===== | ===== Boot Device Selection (S3) ===== | ||
To select the desired boot medium set the DIP switches S3, S9 accordingly | To select the desired boot medium set the DIP switches S3, S9 accordingly | ||
- | ==== SD card ==== | + | <grid> |
- | <wrap round important 60%>only for TQMLS102xA | + | <col sm=" |
- | ^ |::: ^ | + | <panel type=" |
- | ^ |::: ^ | + | <WRAP centeralign> |
- | ^ DIP |::: ^ 1 ^ 2 ^ 3 ^ 4 | | + | [size=150%]**S3**[/size] |
- | ^ ON |:::| • | • ^ ^ ^ | + | {{ :en:dip_4_11xx.png? |
- | ^ OFF |:::| | ^ ^ ^ | + | <alert type=" |
- | \\ | + | </ |
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | |||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S3**[/ | ||
+ | {{ : | ||
+ | <alert type=" | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | </ | ||
+ | <col sm=" | ||
+ | |||
+ | <panel type=" | ||
+ | <WRAP centeralign> | ||
+ | [size=150%]**S3**[/ | ||
+ | {{ : | ||
+ | S3-2 ON: TQMLS102xA without eMMC \\ | ||
+ | S3-2 OFF: TQMLS102xA with eMMC | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
+ | </ | ||
- | ==== eMMC ==== | ||
- | <wrap round info 40%> eMMC is a placement option on TQMLS102xA</ | ||
- | ^ |::: ^ S3 |||| | ||
- | ^ |::: ^ {{ : | ||
- | ^ DIP |::: ^ 1 ^ 2 ^ 3 ^ 4 | | ||
- | ^ ON |:::| • | ^ ^ ^ | ||
- | ^ OFF |:::| | • ^ ^ ^ | ||
- | \\ | ||
- | ==== QSPI ==== | ||
- | ^ |::: ^ S3 |||| | ||
- | ^ |::: ^ {{ : | ||
- | ^ DIP |::: ^ 1 ^ 2 ^ 3 ^ 4 | | ||
- | ^ ON |:::| | °((TQMLS102xA without eMMC)) | ||
- | ^ OFF |:::| • | °((TQMLS102xA with eMMC)) | ||
- | \\ | ||
===== CPLD Function Selection (S9) ===== | ===== CPLD Function Selection (S9) ===== | ||
\\ | \\ | ||
- | ==== S9 DIP switch 1 + 2 ==== | ||
- | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
^ S9 ^ DIP 1 ^ DIP 2 ^ | ^ S9 ^ DIP 1 ^ DIP 2 ^ | ||
^ HDMI | ON | ON | | ^ HDMI | ON | ON | | ||
Line 45: | Line 57: | ||
^ UCC | ON | OFF | | ^ UCC | ON | OFF | | ||
^ LVDS_RGBINV | ^ LVDS_RGBINV | ||
- | \\ | + | </ |
- | + | </ | |
- | + | ||
- | + | ||
- | ==== S9 DIP switch 3 + 4 ==== | + | |
- | ^ S9 ^ DIP 3 ^ DIP 4 ^ | + | <col sm=" |
+ | <panel type=" | ||
+ | ^ S9 ^ DIP 3 ^ DIP 4 ^ | ||
^ EC1 | ON | ON | | ^ EC1 | ON | ON | | ||
^ CAN1 / CAN2 | OFF | ON | | ^ CAN1 / CAN2 | OFF | ON | | ||
^ SAI1 / SAI2 | ON | OFF | | ^ SAI1 / SAI2 | ON | OFF | | ||
^ Reserved | ^ Reserved | ||
- | \\ | + | </panel> |
- | + | </col> | |
- | + | </grid> | |
- | <WRAP round important> | + | |
- | + | ||
- | <WRAP round info>CPLD mux mode #1 EC1_HDMI matches the default RCW configuration of the TQMLS102xA BSP.\\ | + | |
- | If DIP S9 is not set to one of the CPLD mux modes #1 - #12, the CPLD firmware selects mux mode #1. </WRAP> | + | |
+ | <alert type=" | ||
+ | <callout type=" | ||
+ | CPLD mux mode #1 EC1_HDMI matches the default RCW configuration of the TQMLS102xA BSP.\\ | ||
+ | If DIP S9 is not set to one of the CPLD mux modes #1 - #12, the CPLD firmware selects mux mode #1. </ | ||
- | ^ Function | + | < |
+ | ^ Function | ||
^ #1 EC1 + HDMI | ON | ON | ON | ON | | ^ #1 EC1 + HDMI | ON | ON | ON | ON | | ||
^ #2 EC1 + LVDS | OFF | ON | ON | ON | | ^ #2 EC1 + LVDS | OFF | ON | ON | ON | | ||
Line 77: | Line 88: | ||
^ #9 SAI + HDMI | ON | ON | ON | OFF | | ^ #9 SAI + HDMI | ON | ON | ON | OFF | | ||
^ #10 SAI + LVDS | OFF | ON | ON | OFF | | ^ #10 SAI + LVDS | OFF | ON | ON | OFF | | ||
- | ^ #11 SAI + LVDS | + | ^ #11 SAI + UCC |
^ #12 SAI + LVDS_RGBINV | ^ #12 SAI + LVDS_RGBINV | ||
- | ^ #13 - #16 reserved | + | ^ #13 - #16 reserved |
+ | </ | ||
- | ===== CAN configuration (S2) ===== | ||
- | DIP switch S2 is used to configure the CAN interfaces CAN0 and CAN1. | ||
- | <WRAP centeralign half column> | ||
- | ==== Termination ==== | ||
- | ^ DIP ^ OFF (default) | ||
- | | S2-1 | CAN0 not terminated | ||
- | | S2-2 | CAN1 not terminated | ||
- | </ | ||
- | <WRAP clear></ | ||
- | ===== RS485 configuration (S1) ===== | + | |
+ | ===== Functional DIP Switches ===== | ||
+ | DIP-Switch settings for CAN and RS485. | ||
+ | |||
+ | < | ||
+ | <col sm=" | ||
+ | <panel type=" | ||
+ | DIP switch S2 is used to configure the CAN interfaces CAN1 and CAN2. | ||
+ | ^ DIP ^ OFF (default) | ||
+ | | S2-1 | CAN0 not terminated | ||
+ | | S2-2 | CAN1 not terminated | ||
+ | </ | ||
+ | </ | ||
+ | |||
+ | <col sm=" | ||
+ | <panel type=" | ||
DIP switch S1 is used to configure the RS485 interface. | DIP switch S1 is used to configure the RS485 interface. | ||
- | <WRAP centeralign half column> | + | ^ DIP ^ OFF (default) |
- | ==== Termination ==== | + | | S1-1 | RS485 RxD not terminated |
- | ^ DIP ^ OFF (default) | + | | S1-2 | RS485 TxD not terminated |
- | | S1-1 | RS485 RxD not terminated | + | </panel> |
- | | S1-2 | RS485 TxD not terminated | + | </ |
- | </WRAP> | + | |
+ | </grid> | ||
+ | ---- |