This is an old revision of the document!
Embedded module TQMx80UC Documentation
BIOS Overview
BIOS Overview
| BIOS Revision | BIOS Version | ME Firmware Version | Chipset | PCI Configurations | BIOS Binary |
|---|---|---|---|---|---|
| Rev. 0102 | 05.23.45.19.04 | 12.0.33.1424 | Whiskeylake ULT | 4×1 PCIe Lanes | TQMx80UC_05.23.45.19.04.bin |
| Rev. 0101 | 05.23.45.19.03 | 12.0.33.1424 | Whiskeylake ULT | 4×1 PCIe Lanes | TQMx80UC_05.23.45.19.03.bin |
| Rev. 0100 | 05.23.45.15.02 | 12.0.33.1424 | Whiskeylake ULT | 4×1 PCIe Lanes | TQMx80UC_05.23.45.15.02.bin |
Changelog
Changelog
05.23.45.19.04
- Change Default configuration
- Added Boot performance mode <Max Non-Turbo Performance>
- Enabled cTDP BIOS Control
- Adapt new GOP Version to TQMx80UC
- Add new GOP Driver 9.0.1098 downloaded by Intel PlatformSW
- Extend Help Text of cTDP 2
- Add H2OUVE Tool Support
- Adapt GOP/VBIOS to improve signal
05.23.45.13.02
- Fix 'ME Image Re-Flash' Option not working correctly
- Adapt help text for Active LFP
- Fix not working EFP2 in VBIOS
- Adapt PCIe Configuration menu
- Integrate SioNct7802y
- Import SioTqmx86 from TQMx60EB module
- Add Switch to disabel LVDS bridge
- Add Switch for COMe Lane configuration
- Add Switch for GPIO/SD-Card configuration
- Hide GPIO/SD-Card information
- Add Swtich for COM Express Serial Handshake
- Hide PCI Express PEG Port Configuration
- Disable End Of Post Message
- Change Default Configuration
- Clock0 assignment <Enabled>
- Clock2 assignment <Enabled>
- Audio DSP <Disabled>
- I2C0 Controller <Disabled>
- I2C1 Controller <Disabled>
- I2C4 Controller <Disabled>
- UART0 Controller <Disabled>
- ISH Controller <Disabled>
- Flash Protection Range Registers (FPRR) <Disabled>
- CNVi Mode <Disabled>
- ACPI D3Cold Support <Disabled>
- Topology (All PCIe Ports) <x1>
- ASPM X (All PCIe Ports) <Disabled>
- L1 Substates (All PCIe Ports) <Disabled>
- Serial IRQ Mode <Continous>
- Package C State Limit <C3>
- PS2 Keyboard and Mouse <Disabled>
- Numlock <On>
- Adapt Setup menu
- Reserve IRQ11 for use with (internal) PCI bus
- Set SMBIOS data
- Add USB touch support
- Adapt VBIOS / GOP configuration
- Enable Usage of SPI flashes not listed
- Add verb table for ALC262 coded on COME6-2 carrier board
- Disable Thunderbolt support
- Decrease Boot Time
- Disabel USB Type C
- Disable SD, eMMC
- Disable EC commands
- Use OemSvcLoadDefaultSetupMenu for 3x reset processing
- Add TQ boot logo
- Add TQ specific GPIO Table
- Disable Ps2 Keyboard in ACPI
- Disable EC support
- Disable End Of Post Message
- Enable USB Hot key Support as default
- Disable BIOS Lock
- Integrate ME FW Corporate 12.0.32.1421
- Disable clock output configuration (ITPXDP, SRC1, SRC3, SRC4, SRC5)
- Set SPI re-binding
- Set USB3.0 to Gen1
- Enable Dual Read and add Winbond and Macronix chip to VSCC Entry
- Set all GPIO voltages to 3,3 Volt
- Adapt version number and string
- Enable build time flag in BIOS setup menu
- Do not only use primary display
- Do not save password in CMOS
- enable Snap-Screen support