MBa28 DIP switch settings
Boot Device Selection (S4 & S5)
To select the desired boot medium set the DIP switches S4 and S5 accordingly.
The following boot modes of the i.MX28 can be selected by the DIP switches S4 and S5 on the MBa28.
SD card
| S4 | S5 | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
 |  |
|||||||||
| DIP | 1 | 2 | 3 | 4 | 1 | 2 | 3 | 4 | ||
| ON | • | • | note | • | N/A | |||||
| OFF | • | • | • | |||||||
It is not possible to boot from SD card with the following Hardware combination TQMa28-A[C,D,E] Rev.02XX and MBa28 ≤ Rev.0105
On-board eMMC
| S4 | S5 | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
 |  |
|||||||||
| DIP | 1 | 2 | 3 | 4 | 1 | 2 | 3 | 4 | ||
| ON | note | N/A | ||||||||
| OFF | • | • | • | • | • | • | ||||
USB Recovery
| S4 | S5 | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
 |  |
|||||||||
| DIP | 1 | 2 | 3 | 4 | 1 | 2 | 3 | 4 | ||
| ON | • | • | note | N/A | ||||||
| OFF | • | • | • | • | ||||||
CAN configuration (S1)
DIP switch S1 is used to configure the CAN interfaces CAN1 and CAN2.
Termination
| DIP | OFF (default) | ON |
|---|---|---|
| S1-1 | CAN1 terminated (120Ω) | CAN1 not terminated |
| S1-2 | CAN2 terminated (120Ω) | CAN2 not terminated |
Slew rate
| DIP | OFF (default) | ON |
|---|---|---|
| S1-3 | CAN1 slew rate configuration disabled | CAN1 slew rate configurable by assembling R282 |
| S1-4 | CAN2 slew rate configuration disabled | CAN2 slew rate configurable by assembling R281 |
RS485 configuration (S3)
DIP switch S3 is used to configure the RS485 interface.
Debug
| DIP | OFF (default) | ON |
|---|---|---|
| S3-1 | No function | No function |
| S3-2 | DEBUG = GND | DEBUG = TQMa28 PU |
Termination
| DIP | OFF (default) | ON |
|---|---|---|
| S3-3 | RS485 RxD terminated (120Ω) | RS485 RxD not terminated |
| S3-4 | RS485 TxD terminated (120Ω) | RS485 TxD not terminated |
Disclaimer
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.