Overview
Current versions & features
Features - 2009.08
U-Boot 2009.08+fsl
| Component | Status | Remarks |
|---|---|---|
| CPU | + | |
| Ethernet | + | |
| e-MMC | + | |
| SD | + | |
| I2C | + | |
| AUART3 | + | |
| Key: + tested | - untested | ? open | ||
QNX Neutrino
QNX Neutrino 6.5.0 SP1
| Device | Interface | Function | Status | Remarks |
|---|---|---|---|---|
| i.MX28 | AUART0 | ? | ||
| i.MX28 | AUART1 | ? | ||
| i.MX28 | AUART2 | ? | not connected on MBa28 | |
| i.MX28 | AUART3 | + | console | |
| i.MX28 | AUART4 | ? | ||
| i.MX28 | Boot ROM | SSP0 | + | eMMC |
| i.MX28 | Boot ROM | SSP1 | + | SD card |
| i.MX28 | Boot ROM | TFTP | + | using U-Boot |
| i.MX28 | DUART | RS-232 | ? | |
| i.MX28 | ENET | ENET-MAC0 | + | Ethernet (IEEE 802.3-2002) |
| i.MX28 | ENET | ENET-MAC1 | + | Ethernet (IEEE 802.3-2002) |
| i.MX28 | FlexCAN | CAN0 | + | |
| i.MX28 | FlexCAN | CAN1 | + | |
| i.MX28 | GPIO | ? | ||
| i.MX28 | I2C0 | Bus access | - | |
| i.MX28 | I2C1 | Bus access | ? | |
| i.MX28 | I2C1 | EEPROM access | ? | |
| i.MX28 | I2C1 | LM73 | ? | Temp. Sensor |
| i.MX28 | LCDIF | TFT Display | + | Display Type FG0700 |
| i.MX28 | LRADC | Touch-Screen Controller | + | |
| i.MX28 | PMU | Battery | ? | |
| i.MX28 | RTC | $ | ||
| i.MX28 | SAIF | SAIF0 | + | |
| i.MX28 | SSP0 | eMMC | $ | |
| i.MX28 | SSP1 | SD card | + | |
| i.MX28 | USB | USB0 (OTG) | + | Mass storage |
| i.MX28 | USB | USB1 (Host only) | + | Mass storage |
| SN75LVDS83B (MBa28) | LVDS | Display | $ | |
| SGTL5000 (MBa28) | HP OUT / LINE OUT | Audio Output | + | |
| SGTL5000 (MBa28) | MIC_IN | Audio Input | ? | |
| Buzzer (MBa28) | GPIO0_24 | ? | ||
| Key: + tested | - untested | ? open issues | $ on request | ||||
Disclaimer
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.