Overview
BSP / Hardware compatibility
The Windows CE BSP only compatible to TQMa28 Module Revision ≤ 0202
Current versions & features
Eboot
Features
| Component | Status | Remarks |
|---|---|---|
| CPU | + | |
| Ethernet | + | |
| Key: + tested | - untested | ? open | ||
Windows CE 6.0
Features
| Components | Status | Comments |
|---|---|---|
| Boot | + | from eMMC and SD-Card |
| Ethernet | + | |
| eMMC | + | |
| ext. SD | + | |
| Display | + | FG0700K5DSSWBG01 |
| CLAA070LC0ACW | ||
| ET0350G0DH6 | ||
| Touch | + | |
| USB | + | HID and Masstorage |
| Sound | + | |
| EEPROM | + | |
| CAN | + | |
| DUART | + | |
| GPIO | + | |
| AUART0 | + | |
| AUART1 | + | |
| AUART2 | + | not connected |
| AUART3 | + | |
| AUART4 | + | |
| Akku/Goldcap | - | |
| Buzzer | + | |
| Key: + tested | - untested | ? open | ||
Changelog
Version 2.22 -15.06.14
- fixed eboot issue downloading Image via Enet2
- fixed EEPROM-MAC-address
- added WRMac as an application
- GPIO - Pindriver
Version 2.20 - 15.01.14
- internal / external Ethernet-Phy has settable clocks now
- supporting eMMC above 2 GB
Version 2.12 - 26.06.13
- support for 10 and 100 MBIT Ethernet,Hotplug support
- fixed UpdateImg.exe - Image update out of the running operation
Version 2.10 - 04.12.12
- patch for PMIC
- speed up system boot
- show splash over the whole boot process
- supporting SDHC
Version 2.02 - 08.07.12
- support for reading MAC addresses from EEPROM
- EEPROM addresses 0 - 0x60 could not used for application any more (not writeable)
- added demo application “WriteMAC”
"WriteMAC" program process
- check eboot menu point 6 for programmed MAC address in eboot
- if MAC address is not set → read from EEPROM )
- set MAC address
- check registry for MAC addresses settings in the system image
- if MAC is not set in registry, MAC address will be setup from eboot
Version 2.01 - 25.06.12
- 10 / 100 Ethernet auto negotation work (no hot plug support)
- changed power settings in XLDR + debug messages from power register in Main() of system image
- configured USB Actve-Sync to predefined COM port
- SD-2 interface could be deactivated, eMMC stays active
- added CLICK (Buzzer)
- version is shown in eboot
- added CAN Stack
Handling
- source + binary - BSP as installer - package
- binary image = test image out of the BSP binarys
Disclaimer
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.