Overview
TQMa53 Rev.0400: Please have a look at known issues!
BSP Version Matrix
| BSP revision | 100 | 101 | 102 | 103 | 104 | 105 | 108 | 109 | 111 | ||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| PTXdist | 2012.04 | 2012.07 | 2012.07 | 2012.07 | 2012.07 | 2013.03 | 2013.03 | 2013.03 | 2013.03 | ||||||
| OSELAS Toolchain | 2011.11 | 2011.11 | 2011.11 | 2011.11 | 2011.11 | 2011.11 | 2012.12.0 | 2012.12.0 | 2012.12.0 | ||||||
| Platform | MBa53 | MBa53 | MBa53 | MBa53 | MBa53 | MBa53 | MBa53 | TBa53 | KB | MBa53 | TBa53 | KB | MBa53 | TBa53 | KB |
| U-Boot | - | - | - | - | - | v2013.01 | v2013.01 | v2013.01 | v2013.01 | v2013.01 | v2013.01 | v2013.01 | v2013.01 | v2013.01 | v2013.01 |
| Barebox | 2012.07 | 2012.07 | 2012.07 | 2012.07 | 2012.07 | v2012.07 | v2012.07 | - | - | v2012.07 | - | - | v2012.07 | - | - |
| Linux Kernel | 3.0 | 3.5 | 3.5 | 3.5 | 3.5 | 3.9 | 3.9 | 3.11 | 3.9 | 3.9 | 3.11 | 3.9 | 3.9 | 3.11 | 3.9 |
| Qt Version | 4.8.0 | 4.8.2 | 4.8.2 | 4.8.2 | 4.8.2 | 4.8.4 | 4.8.4 | 4.8.4 | 4.8.4 | 4.8.4 | 4.8.4 | 4.8.4 | 4.8.4 | 4.8.4 | 4.8.4 |
Bootloader
Barebox Version
Barebox 2012.07
Barebox Features
| Component | Status | Remarks |
|---|---|---|
| CPU | + | i.MX53, silicon rev 2.1 (Cortex A8) |
| Ethernet | + | 1 x FEC |
| USB - Ethernet Bridge not planned | ||
| USB 2.0 | not planned | |
| eSDHC | + | SD card / eMMC |
| UART | + | |
| I²C | - | on request |
| SPI | - | on request |
| GPIO | - | on request |
| Key: + tested | - untested | ? open | ||
u-boot Version
u-boot 2013.01
u-boot Features
| Component | Status | Remarks |
|---|---|---|
| CPU | + | i.MX53, silicon rev 2.1 (Cortex A8) |
| Ethernet | + | 1 x FEC |
| USB - Ethernet Bridge not planned | ||
| USB 2.0 | on request | |
| eSDHC | + | SD card / eMMC |
| UART | + | |
| I²C | + | |
| GPIO | on request | |
| IIM | on request | |
| SPI | on request | |
| Key: + tested | - untested | ? open | ||
Operating System
Version
Linux 3.9 (BSP 0105)
Linux 3.5 (up to BSP 0104)
Features
| Device | Component | Status | Version | BSP rev. | Remarks |
|---|---|---|---|---|---|
| i.MX53 | CPU | + | 3.5 / 3.9 | 0100 | i.MX53 rev 2.1 (Cortex A8) |
| Ethernet (FEC) | + | 3.5 / 3.9 | 0100 | ||
| DVI Display | + | 3.5 / 3.9 * | 0101 | for Rev 0102 see here for a fix | |
| LVDS Display | + | 3.5 / 3.9 * | 0101 | see Change from DVI to LVDS output Output clone only |
|
| parallel Display | + | 3.5 / 3.9 * | 0101 | see Change from DVI to parallel LCD | |
| VGA | + | 3.9 * | 0105 | see Change from DVI to VGA | |
| USB 2.0 | + | 3.5 / 3.9 * | 0102 | OTG Host, see howto configure OTG port | |
| eSDHC | + | 3.5 / 3.9 | 0101 | SD-CARD / eMMC | |
| SATA | + | 3.9 | 0105 | only with u-boot | |
| GPIO | + | 3.5 / 3.9 | 0100 | ||
| SPI | + | 3.5 / 3.9 | 0102 | known to be work on customized base boards | |
| UART | + | 3.5 / 3.9 | 0100 | ||
| I²C | + | 3.5 / 3.9 | 0100 | EEPROM, Temprature sensor, GPIO expander | |
| CAN | + | 3.5 / 3.9 | 0101 | ||
| Audio | + | 3.5 / 3.9 | 0103 | SDMA firmware needed, see here | |
| RTC (PMIC) | + | 3.9 * | 0105 | ||
| Touch (PMIC) | + | 3.9 * | 0105 | ||
| Touch (RS232 / USB) | + | 3.5 / 3.9 | 0102 | ||
| GPU | + | 3.5 / 3.9 * | 0104 | tested with Freescale binaries, see here | |
| VPU | + | 3.9 * | 0105 | CODA firmware needed, see here | |
| CSI | $ | on request | |||
| EIM | $ | on request tested on custom mainboard with 16 bit SRAM |
|||
| MBa53(LAN9514) | Ethernet | + | 3.9 | 0105 | automatic MAC configuration not implemented |
| USB 2.0 | + | 3.5 / 3.9 * | 0102 | 2 x Host | |
| Key: + tested | - untested | ? open | * patches in BSP | $ on request | |||||
Downloads
Disclaimer
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.