Operating System
Supported Features
| TQ Product | Chip | Interface | Function | Pre-release | Remarks |
|---|---|---|---|---|---|
| TQMa57xx | AM57xx | DCAN1 | CAN0 | • | |
| AM57xx | DCAN2 | CAN1 | • | ||
| AM57xx | DEBUG | JTAG | • | tested with XDS200 USB Debug Probe | |
| AM57xx | GMAC0 | RGMII | • | ||
| AM57xx | GMAC1 | RGMII | • | ||
| AM57xx | I2C1 | I2C devices | • | See onboard I2C devices | |
| AM57xx | I2C4 | I2C devices | • | See onboard I2C devices | |
| AM57xx | I2S | Audio | |||
| AM57xx | GPIO | • | |||
| AM57xx | MMC1 | SD Card | • | ||
| AM57xx | MMC2 | eMMC | • | ||
| AM57xx | MMC4 | SDIO | SDIO 4 Bit Interface | ||
| AM57xx | PCIe | PCIe Lane 0 | PCIe | ||
| AM57xx | PCIe | PCIe Lane 1 | mPCIe | ||
| AM57xx | PRUSS1 | PRU_ETH0 | • | ||
| AM57xx | PRUSS2 | PRU_ETH1 | |||
| AM57xx | QSPI | QSPI NOR | • | ||
| AM57xx | SATA | Serial ATA Revision 3.0 | • | ||
| AM57xx | UART3 | RS232 | • | Default console | |
| AM57xx | UART10 | RS485 | • | ||
| AM57xx | USB2 | OTG | |||
| AM57xx | USB3 | Host / USB Hub TUSB8041 | • | ||
| MBa57xx | TUSB8041 | USB3.0 | Host 1 | • | |
| TUSB8041 | USB3.0 | Host 2 | • | ||
| TUSB8041 | USB3.0 | Host 3 | • | ||
| TUSB8041 | USB3.0 | USB4604 | • | ||
| USB4604 | USB2.0 | Host 1 | Available over X55 | ||
| USB4604 | USB2.0 | Host 2 | Available over X56 | ||
| USB4604 | USB2.0 | USB SATA | Available over X26 | ||
| USB4604 | USB2.0 | USB PCIe | • | Available over X29 |
Onboard I2C devices
| I2C bus | TQMa57xx | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| I2C1 | 0x12 PMIC DVS | 0x1F Tempsensor SE97BTP | 0x37 EEPROM SW-Protect | 0x58 PMIC Power Registers | 0x59 PMIC Interface and auxiliaries | 0x5A PMIC Trimming and test | 0x5B PMIC OTP | 0x54 EEPROM | 0x57 EEPROM SE97BTP | 0x5C EEPROM | 0x68 RTC DS1339 |
|
| I2C bus | MBa57xx | |||||
|---|---|---|---|---|---|---|
| I2C4 | 0x18 Audio Codec | 0x20 PCA9555 | 0x21 PCA9554 | 0x2D USB Hub | 0x41 Touchcontroller |
|
Disclaimer
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.