Work in Progress
MBa57xx DIP switch settings
Boot Device Selection (S1, S2)
To select the desired boot medium set the DIP switches S1 and S2 accordingly.
The following boot modes of the i.MX7 can be selected by the DIP switches S1 and S2 on the MBa57xx.
SD Card
| S1 | S2 | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
 |  |
|||||||||||||||||
| DIP | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | ||
| ON | • | • | • | • | ||||||||||||||
| OFF | • | • | • | • | • | • | • | • | • | • | • | • | ||||||
eMMC
| S1 | S2 | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
 |  |
|||||||||||||||||
| DIP | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | ||
| ON | • | • | • | |||||||||||||||
| OFF | • | • | • | • | • | • | • | • | • | • | • | • | • | |||||
QSPI NOR
| S1 | S2 | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
 |  |
|||||||||||||||||
| DIP | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | ||
| ON | • | • | • | • | • | • | ||||||||||||
| OFF | • | • | • | • | • | • | • | • | • | • | ||||||||
CAN configuration (S5)
DIP switch S5 is used to configure the CAN interfaces CAN1 and CAN2.
Termination
| DIP | OFF (default) | ON |
|---|---|---|
| S5-1 | CAN1 not terminated | CAN1 interface terminated (120Ω) |
| S5-2 | CAN2 not terminated | CAN2 interface terminated (120Ω) |
RS485 configuration (S6)
DIP switch S6 is used to configure the RS485 interface.
Termination
| DIP | OFF (default) | ON |
|---|---|---|
| S6-1 | RS485 RxD not terminated | RS485 RxD terminated (120Ω) |
| S6-2 | RS485 TxD not terminated | RS485 TxD terminated (120Ω) |
Disclaimer
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.