| Feature | BSP Revision | Remarks |
| TQ Product | Chip | Interface | Function | 0100 not released yet |
| TQMa6ULxL | i.MX6UL | ENET1 | RMII
(10/100 Mbit/s) | • | |
| i.MX6UL | ENET2 | RMII
(10/100 Mbit/s) | • | |
| i.MX6UL | FLEXCAN1 | CAN 2.0B | • | |
| i.MX6UL | FLEXCAN2 | CAN 2.0B | • | |
| i.MX6UL | GPIO | 8x GPIO | • | Available on pinheader X23 |
| i.MX6UL | I2C2 | | • | Available on pinheader X23 |
| i.MX6UL | I2C4 | I2C devices | • | See supported onboard I2C devices |
| i.MX6UL | eLCDIF | Parallel LCD | • | 24-bit interface available via X19 |
| i.MX6UL | MIPI CSI | | | No device on MBa6ULxL |
| i.MX6UL | PWM4 | Backlight Dimming | • | |
| i.MX6UL | QSPI | Bus access
Memory access | • | |
| i.MX6UL | TEMPMON | | • | Temperature read |
| i.MX6UL | UART1 | TTL/
USB Debug | • | Default console (RS232) on X22 / USB debug connector (X22) selectable with S16-1 on MBA6ULx |
| i.MX6UL | UART3 | RS232 | | Available via X22 |
| i.MX6UL | UART6 | TTL | • | Available via X23 |
| i.MX6UL | USB_Host | USB2514 | • | |
| i.MX6UL | USB_OTG1 | Host | • | |
| i.MX6UL | USB_OTG1 | OTG | | tested with usb serial gadget |
| i.MX6UL | USB_OTG2 | Host | • | Only Host supported |
| i.MX6UL | USB_OTG2 | OTG | | Shared with USB2514 Hub [4:1] |
| i.MX6UL | uSDHC | uSDHC1 SD Card 4 bit connection
uSDHC2 eMMC 8 bit connection | • | |
| MBa6ULxL | PCA9554BS | I2C GPIO expander | • | | |
| SIM | | | | Not tested / available on Connector X12 on MBa6ULxL |
| STMPE811 | resitive touch controller | | | Connected to I2C4 on MBa6ULxL
Not tested |
| USB2514 | USB1
available on Connector X16 | Host 1 | • | |
| USB2514 | USB2
available on Connector X16 | Host 2 | • | |
| USB2514 | USB3
available on Connector X25 | Host 3 | • | |
| USB2514 | USB4
available on pinheader X24 | Host 4 | • | |
| SNVS | Reset | Reset
PMIC-Reset
Power-Down
Wake-Up | • | |
| I2C bus | | TQMa6ULxL | | MBa6ULxL |
| I2C4 | 0x08
PMIC | 0x1A
Tempsensor | 0x50
EEPROM | 0x52
EEPROM | 0x68
RTC | 0x22
GPIO Expander | 0x41
Touch Controller |
Disclaimer
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge.
The software included in the shipment has been configured individually for the starter kits.
The software is only intended to evaluate the module.
The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH.
TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.