Starterkit Interfaces and Functions

Audio

Audio Connector Overview

Connector Function
X8 Microphone
X9 Line In
X10 Line Out

Audio Connector Location

Play Audio on

A simple test sound can be played with the commandline tool speaker-test.
Headphones or active speakers have to be connected to X10 on . 

speaker-test --channels 2 --test wav -D sysdefault:CARD=tqtlv320aic32x

You can also play your own audio files using aplay 

aplay <file>

e.g. 

aplay test.wav
Please notice that no audio test files are available in the default image.

Record Audio via Line-In on 

arecord -f cd test.wav
The audio settings can be altered using amixer or alsamixer

Buttons

GPIO Button Overview

Reference Button

GPIO Button Location

The buttons are available in the sysfs via the device and can be tested with the evtest tool. 






“|device=”/dev/input/event1“|test=“evtest /dev/input/event1”}}



CAN
CAN configuration



DIP switches SW1 and SW2 are used to configure the CAN interfaces CAN0 and CAN1.




	
	

		  Function    SWx-1    SWx-2
	

	
	

		  CAN-Bus not terminated    OFF    OFF  
	

	

		  not defined (illegal state)    OFF    ON  
	

	

		  not defined (illegal state)    ON    OFF  
	

	

		  CAN-Bus terminated with 120 Ohm    ON    ON  
	




CAN Loopback


Loopback Test CAN Interface





CAN0 -> CAN1




candump can0&
cansend can1 5A1#11.2233.44556677.88



CAN1 -> CAN0




candump can1&
cansend can0 5A1#11.2233.44556677.88





”}}



— Template dvfs not found.

Ethernet
U-Boot



In U-Boot eth0 is configured as default interface. The IP configuration can be done statically or by a DHCP server in the network.





 IP configuration via DHCP 





For a configuration via a DHCP server, use the dhcp command in U-Boot.





 Static IP configuration 
For a static IP configuration the following, U-Boot environment variables must be set:



setenv ipaddr <ipaddr> 
(e.g.: setenv ipaddr 192.168.100.111)
setenv netmask <netmask> 
(e.g.: setenv netmask 255.255.255.0)


Linux



Both Ethernet interfaces are activated and configured by systemd-network. The configuration files for the interfaces are located in /lib/systemd/network/ these configuration files can be altered to customize the default interface configuration. A documentation of the configuration files can be found here.





For a temporary static configuration the ip command can be used, below some useful ip commands are listed:





Activate a specific interface


e.g. eth0



ip link set eth0 up







Disable a specific interace


e.g. eth0



ip link set eth0 down







Show ip address for a specific interface


e.g. eth0



ip addr show eth0







Show statistic for a specific interface


e.g. eth0



 
ip -s link show eth0 







Set ip address for a specific interface


e.g. eth0



ip addr add 192.168.1.100/24 dev eth0







Show statistic of all interfaces





ip -s link







Set default gateway for a specific interfaces


e.g. set gateway ip 192.168.1.1 for eth0 



ip route add default via 192.168.1.1 dev eth0






If a DHCP server is available in the network environment the ip configuration can be received from it. To do so execute the udhcpc command, by default eth0 is used.


To configure another interface via dhcp the parameter -i  followed by the interface name e.g. eth1 must be given.


e.g. eth1



udhcpc -i eth1 


GPU



Run GPU benchmark with connected display and loaded device tree in fullscreen mode:



glmark2-es2-wayland --fullscreen


I2C



An overview of the onboard i2c devices is available here



U-Boot



Select i2c bus device



i2c dev 1




Show all devices connected to the i2c bus currently selected:



i2c probe


Linux



Detect all devices connected to a i2c bus:



i2cdetect 16


LVDS



TQ offers an optional LVDS Display kit for the . Each Display can be used on its own by using the corresponding device tree.
To allow reusage, the support for each display is separated in a dtsi fragment.





To bring up the display the U-Boot environment has to be adapted accordingly. 



    

  1.  Interrupt boot process in U-boot
    

    2. 

  2.  Set U-Boot environment variable fdt_file with the command setenv fdt_file  
  - Save the envrionment by executing the saveenv'' command
    

    3. 



RTC



To set the hardware clock to the actual time and date use the following commands:



date -s [YYYY.]MM.DD-hh:mm[:ss]
hwclock -w


SPI



The  has three SPI interfaces. They can be found on the extension headers and can be tested with a loopback test.



SPI Overview

	

		 Interface  linux filesystem 
	




Loopback Test SPI Interface



For the loopback test you need a bridge between SPI_MOSI and SPI_MISO:



echo -n -e "\x01\x0F" | spi-pipe -d <spi interface> -s 10000000 | hexdump
(e.g. echo -n -e "\x01\x0F" | spi-pipe -d /dev/spidev1.0 -s 10000000 | hexdump)


Temperature Sensors
USB



With lsusb you can see all connected usb devices. To mount a partition of an usb stick you can excute mount /dev/<partition> <mount dir> (e.g. mount /dev/sdb1 /mnt). This will mount the first partition of sdb to /mnt. To unmount the device execute umount <mount dir> (e.g. umount /mnt).



User LED
User LED Overview

	

		 Reference   LED name  color   linux filesystem 
	




User LED Location



The user LED's are located in .


To change the behaviour a specific LED, the value in the file trigger must be overwritten.



The following values are valid: 



For example set the trigger of  to heartbeat 



echo heartbeat > 





“|location=”/sys/devices/platform/gpio-leds/leds/“|example=”/sys/class/leds/ledb/trigger“}}










Disclaimer


TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge.
The software included in the shipment has been configured individually for the starter kits.
The software is only intended to evaluate the module.
The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH.
TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.