S2 - Boot Device Selection
| SD card | NOR Flash | |||||||||
| S2 | S2 | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
 |  |
|||||||||
| DIP | 1 | 2 | 3 | 4 | 1 | 2 | 3 | 4 | ||
| ON | • | |||||||||
| OFF | • | |||||||||
S3 - SerDes Configuration
| SERDES86 | SERDES88 | |||||||||
| S3 | S3 | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
 | |
|||||||||
| DIP | 1 | 2 | 3 | 4 | 1 | 2 | 3 | 4 | ||
| ON | • | • | ||||||||
| OFF | • | • | • | |||||||
Dip Switches S1 - S4
| S1 | ||
|---|---|---|
| DIP | ON | OFF |
| 1 | GPIO DIP 0 low | GPIO DIP 0 high |
| 2 | GPIO DIP 1 low | GPIO DIP 1 high |
| 3 | GPIO DIP 2 low | GPIO DIP 2 high |
| 4 | XFI_ENSMB# low | XFI_ENSMB# high |
| S2 | ||
|---|---|---|
| DIP | ON | OFF |
| 1 | TDM Interface | DIU – Display Interface |
| 2 | SD Card / eMMC Boot | NOR Flash Boot |
| 3 | T1024 USB-Clock (CPU Ball D3) | T1042 USB-Clock (CPU Ball F8) |
| 4 | Serdes PLL1 clock = 156.25 MHz | Serdes PLL1 clock = 100 MHz |
| S3 | ||
|---|---|---|
| DIP | ON | OFF |
| 1 | Lane C: SGMII | Lane C: QSGMII |
| 2 | Lane E: miniPCIe | Lane E: Aurora |
| 3 | Lane G: miniPCIe | Lane G: SGMII or SATA |
| 4 | Lane G: SGMII | Lane G: SATA |
| S4 | ||
|---|---|---|
| DIP | ON | OFF |
| 1 | DVDD=3.3 V | DVDD=1.8 V |
| 2 | EVDD=3.3 V | EVDD=1.8 V |
| 3 | CVDD=3.3 V | CVDD=1.8 V |
| 4 | SDHC Boot | Other Boot source |
| S9 | ||
|---|---|---|
| DIP | ON | OFF |
| 1 | D21 REFCLK 156.25 MHz | D21 REFCLK 125 MHz |
| 2 | D21 Config QSGMII to Copper | D21 Config SGMII to Copper |
WORK IN PROGRESS
STKT104x DIP switch settings
Boot Configuration
Use DIP switches S1, S2, S3 and S4 on the STKT104x to configure one of the following boot devices.
SD card
| S1 | S2 | S3 | S4 | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
 |  | |  |
|||||||||||||||||
| DIP | 4 | 3 | 2 | 1 | 4 | 3 | 2 | 1 | 4 | 3 | 2 | 1 | 4 | 3 | 2 | 1 | ||||
| OFF | • | • | • | • | • | • | • | • | • | • | • | |||||||||
| ON | • | • | • | • | • | |||||||||||||||
NOR Flash
| S1 | S2 | S3 | S4 | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| | | |  |
|||||||||||||||||
| DIP | 4 | 3 | 2 | 1 | 4 | 3 | 2 | 1 | 4 | 3 | 2 | 1 | 4 | 3 | 2 | 1 | ||||
| OFF | • | • | • | • | • | • | • | • | • | • | • | • | • | |||||||
| ON | • | • | • | |||||||||||||||||
TQMT1040 SerDes Configuration (0x66)
| S3 | S9 | |||||||
|  |
|||||||
|---|---|---|---|---|---|---|---|---|
| DIP | 1 | 2 | 3 | 4 | 1 | 2 | ||
| ON | • | |||||||
| OFF | • | • | • | • | • | |||
TQMT1040
| Ethernet interface assigment | |||
|---|---|---|---|
| X30 | X37 | ||
| * | * | fm1-mac3 | not used |
| * | * | fm1-mac4 | not used |
* Connected to Ethernet switch on STKT104x (with RCW TQMT1040_SERDES66 and DIP switch configuration for SERDES66)
Dip Switches S1 - S4
| S1 | ||
|---|---|---|
| DIP | ON | OFF |
| 1 | GPIO DIP 0 low | GPIO DIP 0 high |
| 2 | GPIO DIP 1 low | GPIO DIP 1 high |
| 3 | GPIO DIP 2 low | GPIO DIP 2 high |
| 4 | XFI_ENSMB# low | XFI_ENSMB# high |
| S2 | ||
|---|---|---|
| DIP | ON | OFF |
| 1 | TDM Interface | DIU – Display Interface |
| 2 | SD Card / eMMC Boot | NOR Flash Boot |
| 3 | T1024 USB-Clock (CPU Ball D3) | T1042 USB-Clock (CPU Ball F8) |
| 4 | Serdes PLL1 clock = 156.25 MHz | Serdes PLL1 clock = 100 MHz |
| S3 | ||
|---|---|---|
| DIP | ON | OFF |
| 1 | Lane C: SGMII | Lane C: QSGMII |
| 2 | Lane E: miniPCIe | Lane E: Aurora |
| 3 | Lane G: miniPCIe | Lane G: SGMII or SATA |
| 4 | Lane G: SGMII | Lane G: SATA |
| S4 | ||
|---|---|---|
| DIP | ON | OFF |
| 1 | DVDD=3.3 V | DVDD=1.8 V |
| 2 | EVDD=3.3 V | EVDD=1.8 V |
| 3 | CVDD=3.3 V | CVDD=1.8 V |
| 4 | SDHC Boot | eMMC |
| S9 | ||
|---|---|---|
| DIP | ON | OFF |
| 1 | D21 REFCLK 156.25 MHz | D21 REFCLK 125 MHz |
| 2 | D21 Config QSGMII to Copper | D21 Config SGMII to Copper |
Disclaimer
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.
TQ-Systems GmbH provides the Board Support Packages (BSP) free of charge. The software included in the shipment has been configured individually for the starter kits. The software is only intended to evaluate the module. The use of the Board Support Packages (BSP) is only allowed within the scope of functionality described by TQ-Systems GmbH. TQ-Systems GmbH does not accept any liability for all further changes of the Board Support Package and for any damage resulting from its use.