5.12.09.53.15

5.12.09.44.13

5.11.51.0024.01

• FAT formated USB-Stick with atleast >32 MiB storage
• Latest BIOS-Update-USB Stick Zip (TQ Support Wiki Downloads)

- Copy Insyde Firmware Flash Tool to USB-Stick

<USB key>
    ├───H2OFFT-Sx64.efi
 

The BIOS-Update-USB Stick is now ready for updating and flashing BIOS Images.
For further Information please see the BIOS Update section.

• BIOS-Update-USB Stick
• BIOS File (e.g. TQMx70EB)
• Copy BIOS File to BIOS-Update-USB Stick

<USB key>
    ├───H2OFFT-Sx64.efi
    ├───TQMx60_70EB_5.12.09.53.15.bin    

• Insert BIOS-Update-USB Stick stick to a Starterkit USB port
• First enable 'FW Image Re-Flash' option in the BIOS Menu (Setup Utility > Advanced > PCH-FW Configuration >Firmware Update Configuration > Me FW Image Re-Flash > enable)
• F10 to save the settings and reboot the system
• After reboot navigate into the EFI Shell (Boot Manager > Internal EFI Shell)
• After starting the EFI Shell Switch path to the USB stick by typing fs0:. This depends on the amount of connected mass storage devices with command ls you can check the content of the path.
• Launch BIOS update
  

fs0:\> H2OFFT-Sx64.efi <BIOS_Image>.bin –me –desc –bios –all <Enter>

Example

 H2OFFT-Sx64.efi TQMx60_70EB_5.12.09.53.15.bin –me –desc –bios –all

⇒ BIOS will reboot into EFI shell after the update has finished succesfully

• Leave EFI shell
  

Shell> exit

• Select “Boot Manager”
• Select desired boot device (e.g. Internal HD)
  ⇒ System will reboot from selected boot device

This instruction guides you through the procedure of replacing the Bootlogo using the Insyde UEFI/BIOS tool called H2OLRT (Logo Replacement Tool).

Prepare BIOS-Update-USB Stick and add the following components:

• Logo Replacement Tool (H2OLRT-Sx64.efi)
• Appropriate BIOS file for your TQ module (e.g. TQMx60_70EB_5.12.09.53.15.bin)
• Picture formated as *.jpg (e.g. example_picture.jpg)

• Insert the BIOS-Update-USB Stick to a Starterkit USB port
• Boot up the system and navigate into the EFI Shell (Boot Manager > Internal EFI Shell)
• After starting the EFI Shell Switch path to the USB stick by typing fs0:.This depends on the amount of conected mass storage devices; with command ls you can check the content of the path.
• The generic command and the following example shows how to start the Logo Replacement.

H2OLRT-Sx64.efi –replogo:<SrcBIOSImageName> –logopath:<LogoImagePathName> -logoindex:<IndexNum> –logoconvert:<ConvertNum> –out:<OutBIOSImageName>

Example

H2OLRT-Sx64.efi –replogo:TQMx60_70EB_5.12.09.53.15.bin –logopath:example_picture.jpg -logoindex:4 –logoconvert:1 –out:TQMx60_70EB_5.12.09.53.15_new.bin

<SrcBIOSImageName>
BIOS file in which the logo should be replaced

<LogoImagePathName>
Path and name of the replacement picture

<IndexNum>
Default index, where the picture must be stored:

<ConvertNum> :

• 0 = keep original image's format and dimension
• 1 [default] = auto convert the image's format and dimension
  

<OutBIOSImageName>
path and name of the generated BIOS file

• Next step is to flash the customized BIOS Binary, please see the BIOS Update section.

If there is no Jumper present on the BIOS_DIS1# or BOOT_SEL2_1V8# signal the module will load its BIOS from the internal SPI flash.
If there is a Jumper on the BIOS_DIS1# or BOOT_SEL2_1V8# signal (between signal and GND) the module loads its BIOS from the flash in the SPI socket of the carrier board.

Following external SPI flash devices are supported by the corresponding platform/module: